Cumincad : CUMINCAD Papers : Search Results

CumInCAD is a Cumulative Index about publications in Computer Aided Architectural Design
supported by the sibling associations ACADIA, CAADRIA, eCAADe, SIGraDi, ASCAAD and CAAD futures

PDF papers
References

Hits 1 to 20 of 145

Reformat results as: short short into frame detailed detailed into frame

_id	8ae8
authors	Ayala, D., P. Brunet and Juan (et al)
year	1985
title	Object Representation by Means of Nominimal Division Quadtrees and Octrees
source	ACM Transactions on Graphics. January, 1985. vol. 4: pp. 41-59 : ill. includes bibliography
summary	Quadtree representation of two-dimensional objects is performed with a tree that describes the recursive subdivision of the more complex parts of a picture until the desired resolution is reached. At the end, all the leaves of the tree are square cells that lie completely inside or outside the object. There are two great disadvantages in the use of quadtrees as a representation scheme for objects in geometric modeling system: The amount of memory required for polygonal objects is too great, and it is difficult to recompute the boundary representation of the object after some Boolean operations have been performed. In the present paper a new class of quadtrees, in which nodes may contain zero or one edge, is introduced. By using these quadtrees, storage requirements are reduced and it is possible to obtain the exact backward conversion to boundary representation. Algorithms for the generation of the quadtree, boolean operation, and recomputation of the boundary representation are presented, and their complexities in time and space are discussed. Three- dimensional algorithms working on octrees are also presented. Their use in the geometric modeling of three-dimensional polyhedral objects is discussed
keywords	geometric modeling, algorithms, octree, quadtree, curves, curved surfaces, boolean operations
series	CADline
last changed	2003/06/02 13:58

_id	e191
authors	Fuchs, Henry, Goldfeather, Jack and Hultquist, Jeff P.
year	1985
title	Fast Spheres, Shadows, Textures, Transparencies, and Image Enhancements in Pixel-Planes
source	SIGGRAPH '85 Conference Proceedings. July, 1985. 1985. vol. 19 ; no. 3: pp. 111-120 : ill. includes bibliography
summary	Pixel-planes is a logic-enhanced memory system for raster graphics and imaging. Although each pixel-memory is enhanced with a one-bit ALU, the system's real power comes from a tree of one-bit address that can evaluate linear expressions Ax + By + C for every pixel (x,y) simultaneously, as fast as the ALUs and the memory circuits can accept the results. The development of a variety of algorithms that exploit this fast linear expression evaluation capability has started. The paper reports some of those results. Illustrated in this paper is a sample image from a small working prototype of the Pixel- planes hardware and a variety of images from simulations of a full-scale system. Timing estimates indicate that 30,000 smooth shaded triangles can be generated per second, or 21, 000 smooth-shaded and shadowed triangles can be generated per second, or over 25,000 shaded spheres can be generated per second. Image-enhancement by adaptive histogram equalization can be performed within 4 seconds on a 512 x 512 image
keywords	shadowing, image processing, algorithms, polygons, clipping, computer graphics, technology, hardware
series	CADline
last changed	2003/06/02 10:24

_id	6db4
authors	Karakatsanis, Andreas Georgiou
year	1985
title	Floder: A Floor Designer Expert System
source	Department of Civil Engineering, Carnegie Mellon University, Pittsburgh PA
summary	The use of computers in structural design for the last two decades has been limited to algorithmic and procedural tasks. The use of expert system environments facilitates the implementation of conceptual tasks in computer programs. The goal of this study is to develop an expert system for the structural design of floor framings. FLODER, the resulting expert system, generates, analyzes, and evaluates floor framings for a given architectural plan. Framing generation consists of determination of the locations of structural elements in the architectural plan. Analysis involves an approximation of the dimensions of the slabs. Evaluation numerically ranks all generated framings using heuristic features for the alternatives. FLODER is implemented in OPS5 and LISP. The primary representations used are OPS5 production rules for the knowledge-base, and OPS5 working memory elements, for the context. Tasks amenable to algorithmic approaches are implemented in LISP. FLODER, even in its present state, can be viewed as a useful assistant to a designer. It can rapidly generate and evaluate alternative framings for a given architectural plan and thus increase the work productivity of its users [includes bibliography].
keywords	Knowledge Base, Systems, Design, Architecture, Civil Engineering, Representation, Expert Systems, Floor Plans, Synthesis, Structures
series	CADline
last changed	1999/02/15 15:27

_id	4839
authors	Kripac, Jiri
year	1985
title	Classification of Edges and its Application in Determining Visibility
source	Computer Aided Design. January/ February 1985. vol. 17: pp.30-36 : ill. includes bibliography
summary	A new hidden-line algorithm is proposed for illustrating objects consisting of plane faces. The algorithm determines the degree of edge and classifies edges and faces into contoural and non-contoural. To reduce memory requirements, sequential files and sorting are used. The algorithm is particularly intended for illustrating complex objects, such as curved surfaces approximated by plane faces
keywords	algorithms, hidden lines, curved surfaces, geometric modeling, computer graphics
series	CADline
last changed	1999/02/12 15:08

_id	8298
authors	Quadrel, Richard W. and Chassin, David P.
year	1985
title	Energy Graphics: A Progress Report on the Development of Architectural Courseware
doi	https://doi.org/10.52842/conf.acadia.1985.129
source	ACADIA Workshop ‘85 [ACADIA Conference Proceedings] Tempe (Arizona / USA) 2-3 November 1985, pp. 129-141
summary	Energy Graphics is a technique for determining the energy performance of buildings at the conceptual stage of the architectural design process. Unlike many energy analysis programs, which only produce results after ail of the building information has been supplied, Energy Graphics works with the designer in understanding how early decisions about building form and configuration affect energy use. The Energy Graphics technique is currently being "computerized" on a Sun 2/120 graphics workstation, under a grant by the Inter-University Consortium for Educational Computing. The resulting software will be used in the architectural design curriculum so that students will be able to receive an immediate energy evaluation of their design explorations. For use in the studios, the software must include a powerful graphics interface that allows students to "sketch" their design concepts interactively. The computer will then interpret these sketches as building information, organize them into an integrated database, perform the energy calculations, and inform the student of the results in a graphic format. One of the project's major goals is to provide this graphics interface in the same way that architects think about drawing, and not simply to imitate current computer "drafting" systems. The goals of the project can only be met by developing the software on a powerful workstation system, which provides fast processing time, large memory, multitasking capabilities and high-resolution graphics. This progress report describes our efforts to date on the development of this important software.
series	ACADIA
last changed	2022/06/07 08:00

_id	ce52
authors	Abram, Greg, Weslover, Lee and Whitted, Turner
year	1985
title	Efficient Alias-Free Rendering using Bit-masks and Look-up Tables
source	SIGGRAPH '85 Conference Proceedings. July, 1985. vol. 19 ; no. 3: pp. 53-59 : ill. (some col.). includes bibliography
summary	The authors demonstrate methods of rendering alias-free synthetic images using a precomputed convolution integral. The method is based on the observation that a visible polygon fragment's contribution to an image is solely a function of its position and shape, and that within a reasonable level of accuracy, a limited number of shapes represent the majority of cases encountered in images commonly rendered. The basic technique has been applied to several different rendering algorithms. A version of the newly non-uniform sampling technique implemented in the same program but with different tables values was introduced
keywords	algorithms, computer graphics, anti-aliasing
series	CADline
last changed	2003/06/02 13:58

_id	678e
authors	Aish, Robert
year	1986
title	Three-dimensional Input and Visualization
source	Computer-Aided Architectural Design Futures [CAAD Futures Conference Proceedings / ISBN 0-408-05300-3] Delft (The Netherlands), 18-19 September 1985, pp. 68-84
summary	The aim of this chapter is to investigate techniques by which man-computer interaction could be improved, specifically in the context of architectural applications of CAD. In this application the object being designed is often an assembly of defined components. Even if the building is not actually fabricated from such components, it is usually conceptualized in these terms. In a conventional graphics- based CAD system these components are usually represented by graphical icons which are displayed on the graphics screen and arranged by the user. The system described here consists of three- dimensional modelling elements which the user physically assembles to form his design. Unlike conventional architectural models which are static (i.e. cannot be changed by the users) and passive (i.e. cannot be read by a CAD system), this model is both 'user generated' and 'machine readable'. The user can create, edit and view the model by simple, natural modelling activities and without the need to learn complex operating commands often associated with CAD systems. In particular, the user can view the model, altering his viewpoint and focus of attention in a completely natural way. Conventional computer graphics within an associated CAD system are used to represent the detailed geometry which the different three-dimensional icons may represent. In addition, computer graphics are also used to present the output of the performance attributes of the objects being modelled. In the architectural application described in this chapter an energy- balance evaluation is displayed for a building designed using the modelling device. While this system is not intended to offer a completely free-form input facility it can be considered to be a specialist man-machine interface of particular relevance to architects or engineers.
series	CAAD Futures
email
last changed	2003/11/21 15:15

_id	cc15
authors	Ansaldi, Silvia, De Floriani, Leila and Falcidieno, Bianca
year	1985
title	Geometric Modeling of Solid Objects by Using a Face Adjacency Graph Representation
source	SIGGRAPH '85 Conference Proceedings. July, 1985. vol. 19 ; no. 3: pp. 131-139 : ill. includes bibliography
summary	A relational graph structure based on a boundary representation of solid objects is described. In this structure, called Face Adjacency Graph, nodes represent object faces, whereas edges and vertices are encoded into arcs and hyperarcs. Based on the face adjacency graph, the authors define a set of primitive face-oriented Euler operators, and a set of macro operators for face manipulation, which allow a compact definition and an efficient updating of solid objects. The authors briefly describe a hierarchical graph structure based on the face adjacency graph, which provides a representation of an object at different levels of detail. Thus it is consistent with the stepwise refinement process through which the object description is produced
keywords	geometric modeling, graphs, objects, representation, data structures,B-rep, solid modeling, Euler operators
series	CADline
last changed	2003/06/02 10:24

_id	acfe
authors	Archea, John
year	1985
title	Architecture's Unique Position Among the Disciplines : Puzzle-Making vs. Problem Solving
source	CRIT XV, The Architectural Student Journal. Summer, 1985. pp. 20-22
summary	Most disciplines involved in the building process, i.e., programmers, space planners, and engineers work in what may be described as a problem solving mode. They state desired effects as explicit performance criteria before they initiate a decision process and test alternative solutions against those criteria until a fit is attained which falls within known probabilities of success. Architects, however are not problem solvers and they are not seeking explicit information when they design how buildings work. Architects are puzzle- makers, They are primarily concerned with unique design concepts. It is through the act of designing, or puzzle- making, that the architect learn what they want to accomplish and how. With regard to the making of buildings, places or experiences, the architect is a puzzle-maker surrounded by a group of problem solvers who address separate pieces of the puzzle
keywords	puzzle making, design process, problem solving, architecture
series	CADline
last changed	1999/02/12 15:07

_id	2ae0
authors	Bairstow, Jeffrey N.
year	1985
title	Chip Design Made Easy
source	high Technology. June, 1985. pp. 18-25 : ill. includes bibliography: p. 74
summary	The combination of powerful engineering workstations and novel software tools is making custom chip design economical even for engineers without the specific training. The availability of new automated design technology is promoted by the changing market dynamics. The design of an integrated circuit, with hardware choices, is described
keywords	business, AI, electrical engineering, hardware
series	CADline
last changed	2003/06/02 13:58

_id	2730
authors	Balkovich, Edward, Lerman, Steven and Parmelee, Richard P.
year	1985
title	Computing in Higher Education : The ATHENA Experience
source	communications of the ACM. November, 1985. vol. 28: pp. 1214- 1224
summary	In this article the use of computation in higher education is approached from the broad sense of its actual use in the curriculum. The authors try to identify areas where current educational methods have observable deficiencies that might be alleviated by the use of appropriate software/hardware combinations. Project ATHENA at MIT is the example the article is based on
keywords	networks, software, hardware, UNIX, education
series	CADline
last changed	2003/06/02 13:58

_id	c89d
authors	Bancroft, Pamela J.
year	1987
title	The Integration of Computing into Architectural Education Through Computer Literate Faculty
doi	https://doi.org/10.52842/conf.acadia.1987.109
source	Integrating Computers into the Architectural Curriculum [ACADIA Conference Proceedings] Raleigh (North Carolina / USA) 1987, pp. 109-120
summary	This paper discusses the apparent correlation between faculty computer literacy and the success of integrating computing into architectural education. Relevant questions of a 1985 national survey which was conducted to study the historical development of faculty computer utilization are analyzed and interpreted. The survey results are then used as the basis for a series of recommendations given for increasing computer literacy among faculty in architectural schools, thus increasing the integration of computing.
series	ACADIA
last changed	2022/06/07 07:54

_id	2928
authors	Barsky, Brian A. and De Rose, Tony D.
year	1985
title	The Beta2-spline : A Special Case of the Beta-spline Curve and Surface Representation
source	IEEE Computer Graphics and Applications September, 1985. vol. 5: pp. 46-58 : ill. includes bibliography.
summary	This article develops a special case of the Beta-spline curve and surface technique called the Beta2-spline. While a general Beta-spline has two parameters (B1 and B2) controlling its shape, the special case presented here has only the single parameter B2. Experience has shown this to be a simple but very useful special case that is computationally more efficient than the general case. Optimized algorithms for the evaluation of the Beta2-spline basis functions and rendering of Beta2-spline curves and surfaces via subdivision are presented. This technique is proving to be quite useful in the modeling of complex shapes. The representation is sufficiently general and flexible so as to be capable of modeling irregular curved-surface objects such as automobile bodies, aircraft fuselages, ship hulls, turbine blades, and bottles
keywords	B-splines, curved surfaces, computational geometry, representation, algorithms, computer graphics, rendering
series	CADline
last changed	2003/06/02 14:41

_id	c50a
authors	Bartschi, Martin
year	1985
title	An Overview of Information Retrieval Subjects
source	IEEE Computer. May, 1985. vol. 18: pp. 67-84 : ill. includes bibliography
summary	The aim of an information retrieval system is to find information items relevant to an information need. As relevance is a kind of similarity relation between the concepts represented by the information item and those represented by the formulation of the information need, it is not astonishing to discover that the class of possible query forms -formulations of the information needs - is the same as the class of possible representations of information items. This article overviews current research problems in information structure and query evaluation
keywords	database, information, queries, systems
series	CADline
last changed	1999/02/12 15:07

_id	2d64
authors	Batori, D.S. and Kim, W.
year	1985
title	Modeling Concepts for VLSI CAD Objects
source	ACM Transactions on Database Systems 10 No. 3 - pp. 322-346
summary	VLSI CAD applications deal with design objects that have an interface description and an implementation description. Versions of design objects have a common interface but differ in their implementations. A molecular object is a modeling construct which enables a database entity to be represented by two sets of heterogeneous records, one set describes the object's interface and the other describes its implementation. Thus a reasonable starting point for modeling design objects is to begin with the concept of molecular objects. In this paper, we identify modeling concepts that are fundamental to capturing the semantics of VLSI CAD design objects and versions in terms of molecular objects. A provisional set of user operations on design objects, consistent with these modeling concepts, is also defined. The modeling framework that we present has been found useful for investigating physical storage techniques and change notification problems in version control. REFERENCES
series	journal paper
last changed	2003/11/21 15:16

_id	ddssar0206
id	ddssar0206
authors	Bax, M.F.Th. and Trum, H.M.G.J.
year	2002
title	Faculties of Architecture
source	Timmermans, Harry (Ed.), Sixth Design and Decision Support Systems in Architecture and Urban Planning - Part one: Architecture Proceedings Avegoor, the Netherlands), 2002
summary	In order to be inscribed in the European Architect’s register the study program leading to the diploma ‘Architect’ has to meet the criteria of the EC Architect’s Directive (1985). The criteria are enumerated in 11 principles of Article 3 of the Directive. The Advisory Committee, established by the European Council got the task to examine such diplomas in the case some doubts are raised by other Member States. To carry out this task a matrix was designed, as an independent interpreting framework that mediates between the principles of Article 3 and the actual study program of a faculty. Such a tool was needed because of inconsistencies in the list of principles, differences between linguistic versions ofthe Directive, and quantification problems with time, devoted to the principles in the study programs. The core of the matrix, its headings, is a categorisation of the principles on a higher level of abstractionin the form of a taxonomy of domains and corresponding concepts. Filling in the matrix means that each study element of the study programs is analysed according to their content in terms of domains; thesummation of study time devoted to the various domains results in a so-called ‘profile of a faculty’. Judgement of that profile takes place by committee of peers. The domains of the taxonomy are intrinsically the same as the concepts and categories, needed for the description of an architectural design object: the faculties of architecture. This correspondence relates the taxonomy to the field of design theory and philosophy. The taxonomy is an application of Domain theory. This theory,developed by the authors since 1977, takes as a view that the architectural object only can be described fully as an integration of all types of domains. The theory supports the idea of a participatory andinterdisciplinary approach to design, which proved to be awarding both from a scientific and a social point of view. All types of domains have in common that they are measured in three dimensions: form, function and process, connecting the material aspects of the object with its social and proceduralaspects. In the taxonomy the function dimension is emphasised. It will be argued in the paper that the taxonomy is a categorisation following the pragmatistic philosophy of Charles Sanders Peirce. It will bedemonstrated as well that the taxonomy is easy to handle by giving examples of its application in various countries in the last 5 years. The taxonomy proved to be an adequate tool for judgement ofstudy programs and their subsequent improvement, as constituted by the faculties of a Faculty of Architecture. The matrix is described as the result of theoretical reflection and practical application of a matrix, already in use since 1995. The major improvement of the matrix is its direct connection with Peirce’s universal categories and the self-explanatory character of its structure. The connection with Peirce’s categories gave the matrix a more universal character, which enables application in other fieldswhere the term ‘architecture’ is used as a metaphor for artefacts.
series	DDSS
last changed	2003/11/21 15:16

_id	ddss9408
id	ddss9408
authors	Bax, Thijs and Trum, Henk
year	1994
title	A Taxonomy of Architecture: Core of a Theory of Design
source	Second Design and Decision Support Systems in Architecture & Urban Planning (Vaals, the Netherlands), August 15-19, 1994
summary	The authors developed a taxonomy of concepts in architectural design. It was accepted by the Advisory Committee for education in the field of architecture, a committee advising the European Commission and Member States, as a reference for their task to harmonize architectural education in Europe. The taxonomy is based on Domain theory, a theory developed by the authors, based on General Systems Theory and the notion of structure according to French Structuralism, takes a participatory viewpoint for the integration of knowledge and interests by parties in the architectural design process. The paper discusses recent developments of the taxonomy, firstly as a result of a confrontation with similar endeavours to structure the field of architectural design, secondly as a result of applications of education and architectural design practice, and thirdly as a result of theapplication of some views derived from the philosophical work from Charles Benjamin Peirce. Developments concern the structural form of the taxonomy comprising basic concepts and levelbound scale concepts, and the specification of the content of the fields which these concepts represent. The confrontation with similar endeavours concerns mainly the work of an ARCUK workingparty, chaired by Tom Marcus, based on the European Directive from 1985. The application concerns experiences with a taxonomy-based enquiry in order to represent the profile of educational programmes of schools and faculties of architecture in Europe in qualitative and quantitative terms. This enquiry was carried out in order to achieve a basis for comparison and judgement, and a basis for future guidelines including quantitative aspects. Views of Peirce, more specifically his views on triarchy as a way of ordering and structuring processes of thinking,provide keys for a re-definition of concepts as building stones of the taxonomy in terms of the form-function-process-triad, which strengthens the coherence of the taxonomy, allowing for a more regular representation in the form of a hierarchical ordered matrix.
series	DDSS
last changed	2003/08/07 16:36

_id	ddss9409
id	ddss9409
authors	Beekman, Solange and Rikhof, Herman G.A.
year	1994
title	Strategic Urban Planning in the Netherlands
source	Second Design and Decision Support Systems in Architecture & Urban Planning (Vaals, the Netherlands), August 15-19, 1994
summary	Since the mid-1980s, several Dutch towns have initiated many urban planning and design activities for their existing area. This represented a shift in that previous urban planning projects typicallyconcerned expansion in the outskirts of the city, or urban renewal. The complex and expensive renovation of the existing housing stock rarely allowed a deep interest in urban design. Since 1985, attention shifted from the housing stock to the city as a whole. Furthermore, public andprivate actors increasingly become involved in the planning process. It became clear that a more comprehensive plan for the whole existing town or region was needed. Conventional planning instruments were considered ill-suited for this new challenge. The paper discusses promising attempts of various urban planning instruments to get a stronger but also more flexible hold on thetransformation of the urban planning area in the Netherlands. These new planning instruments have three common characteristics: (i) they give special attention to the different levels of urban management needed for different urban areas, (ii) these strategic plans provide an integral view on the urban developments, and (iii) these plans introduce a new strategy to deal with both private initiatives to transform urban sites and monitor wishes, proposals, etc. from inhabitants in the neighbourhoods. A comparative analyses of several cities indicates, however, that, in addition to these common characteristics, major differences between their strategic plans exist depending upon their historic patrimonium, economic status and planning tradition.
series	DDSS
email
last changed	2003/08/07 16:36

_id	a619
authors	Bentley, Jon L. and McGeoch, Catherine C.
year	1985
title	Amortized Analyses of Self-Organizing Sequential Search ; Heuristics Programming Techniques and Data Structures
source	communications of the ACM April, 1985. vol. 28: pp. 404-411 : ill. includes bibliography.
summary	Amortization is used to analyze the heuristics in a worst- case sense. The relative merit of the heuristics in this analysis is different in the probabilistic analyses. Experiments show that the behavior of the heuristics on real data is more closely described by the amortized analyses than by the probabilistic analyses
keywords	economics, analysis, search, heuristics
series	CADline
last changed	2003/06/02 13:58

_id	4316
authors	Bentley, Jon L.
year	1985
title	Associative Arrays -- Programming Pearls
source	communications of the ACM. June, 1985. vol. 28: pp. 570-576 : ill
summary	Anthropological studies have shown that one's language has a profound effect on one's view of the world. This column is about a language feature outside the Algol heritage: associative arrays. The column examines the associative arrays provided by the AWK language
keywords	techniques, programming, algorithms, data structures
series	CADline
last changed	2003/06/02 13:58

For more results click below: