Cumincad : CUMINCAD Papers : Search Results

CumInCAD is a Cumulative Index about publications in Computer Aided Architectural Design
supported by the sibling associations ACADIA, CAADRIA, eCAADe, SIGraDi, ASCAAD and CAAD futures

PDF papers
References

Hits 1 to 20 of 479

Reformat results as: short short into frame detailed detailed into frame

_id	7135
authors	Arumi-Noe, F.
year	1996
title	Algorithm for the geometric construction of an optimum shading device
source	Automation in Construction 5 (3) (1996) pp. 211-217
summary	Given that there is a need to shade a window from the summer sun and also a need to expose it to the winter sun, this article describes an algorithm to design automatically a geometric construct that satisfies both requirements. The construct obtained represents the minimum solution to the simultaneous requirements. The window may be described by an arbitrary convex polygon and it may be oriented in any direction, and it may be placed at any chosen latitude. The algorithm consists of two sequential steps: first to find a winter solar funnel surface; and the second to clip the surface subject to the summer shading conditions. The article introduces the design problem, illustrates the results through two examples, outlines the logic of the algorithm and includes the derivation of the mathematical relations required to implement the algorithm. This work is part of the MUSES project, which is a long term research effort to integrate Energy Consciousness with Computer Graphics in Architectural Design.
series	journal paper
more	http://www.elsevier.com/locate/autcon
last changed	2003/05/15 21:22

_id	ddssup9601
id	ddssup9601
authors	Aoke, Yoshitsugu and Muraoka, Naoto
year	1996
title	An optimization method of the facility location by genetic algorithm
source	Timmermans, Harry (Ed.), Third Design and Decision Support Systems in Architecture and Urban Planning - Part two: Urban Planning Proceedings (Spa, Belgium), August 18-21, 1996
summary	In planning of community-facilities, it is important to decide the facility location to provide the effective service for residents. The behavior of residents using the facility and the evaluation methods of the location have been studied. But, finding the optimum location is very hard in actual planning because the volume of calculation depends on the number of feasible locating points of facilities. To conquer the difficulty of searching the optimum location, we propose an optimization method using Genetic Algorithm. An alternative of location is expressed by a chromosome. Each chromosome consists of genes, and each gene expresses a located zone of the facility. We gave definitions of genetic procedures; crossing-over, mutation and selection. Alternatives of the facility location are generated by these genetic procedures like as life evolution. For each alternative, the behaviors of users are estimated by a spatial-interaction model, and the facilities that residents in each place choose are determined. The effectiveness of the location is measured by a total sum of distances between the facility and the user. After the confirmation of the effectiveness of our method by applying on ideal example problems, we applied it on the actual problem in Japanese town. By this method we could find the optimum location in about one-third time and effort as compared with the ordinal method.
series	DDSS
last changed	2003/11/21 15:15

_id	c4be
authors	Bock, T., Stricker, D., Fliedner, J. and Huynh, T.
year	1996
title	Automatic generation of the controlling-system for a wall construction robot
source	Automation in Construction 5 (1) (1996) pp. 15-21
summary	In this article we present several important aspects of a software system control. This is designed and developed for a wall assembly robot in an European Esprit III project called ROCCO, RObot assembly system for Computer integrated COnstruction. The system consists of an off-line program for planning of complex assembly tasks and for generating robot actions. The execution is controlled through an adaptive user interface and gives the user the possibilities to switch in an on-line mode command. All the software is designed with the object-oriented concept and implemented in C + +. The wall assembly system is organized on the base of the successive generation of different types of actions, called "Mission", "Task", and "Action". They represent different levels of assembly complexities. Those different actions are organized in a tree structure. Furthermore, the software system can be connected to a CAD-robot simulation software for checking the robot assembly motions. Added to the control system, a recovery module has been implemented for all possible errors during the construction. First the OO-model of the world and of robot activities will be presented. Secondly, several aspects of the algorithm will be explained and at the end we will show the strategy used for the robot motion.
series	journal paper
more	http://www.elsevier.com/locate/autcon
last changed	2003/05/15 21:22

_id	9a0d
authors	Debevec, P.E., Taylor, C.J. and Malik, J.
year	1996
title	Modeling and rendering architecture from photographs: a hybrid geometry- and image-based approach
source	SIGGRAPH'96, New Orleans, Louisiana
summary	We present a new approach for modeling and rendering existing architectural scenes from a sparse set of still photographs. Our modeling approach, which combines both geometry-based and imagebased techniques, has two components. The first component is a photogrammetricmodelingmethodwhich facilitates the recovery of the basic geometry of the photographed scene. Our photogrammetric modeling approach is effective, convenient, and robust because it exploits the constraints that are characteristic of architectural scenes. The second component is a model-based stereo algorithm, which recovers how the real scene deviates from the basic model. By making use of the model, our stereo technique robustly recovers accurate depth from widely-spaced image pairs. Consequently, our approach canmodel large architectural environmentswith far fewer photographs than current image-based modeling approaches. For producing renderings, we present view-dependent texture mapping, a method of compositing multiple views of a scene that better simulates geometric detail on basic models. Our approach can be used to recover models for use in either geometry-based or image-based rendering systems. We present results that demonstrate our approach's ability to create realistic renderings of architectural scenes from viewpoints far from the original photographs.
series	other
last changed	2003/04/23 15:50

_id	20ff
id	20ff
authors	Derix, Christian
year	2004
title	Building a Synthetic Cognizer
source	Design Computation Cognition conference 2004, MIT
summary	Understanding ‘space’ as a structured and dynamic system can provide us with insight into the central concept in the architectural discourse that so far has proven to withstand theoretical framing (McLuhan 1964). The basis for this theoretical assumption is that space is not a void left by solid matter but instead an emergent quality of action and interaction between individuals and groups with a physical environment (Hillier 1996). In this way it can be described as a parallel distributed system, a self-organising entity. Extrapolating from Luhmann’s theory of social systems (Luhmann 1984), a spatial system is autonomous from its progenitors, people, but remains intangible to a human observer due to its abstract nature and therefore has to be analysed by computed entities, synthetic cognisers, with the capacity to perceive. This poster shows an attempt to use another complex system, a distributed connected algorithm based on Kohonen’s self-organising feature maps – SOM (Kohonen 1997), as a “perceptual aid” for creating geometric mappings of these spatial systems that will shed light on our understanding of space by not representing space through our usual mechanics but by constructing artificial spatial cognisers with abilities to make spatial representations of their own. This allows us to be shown novel representations that can help us to see new differences and similarities in spatial configurations.
keywords	architectural design, neural networks, cognition, representation
series	other
type	poster
email
more	http://www.springer.com/computer/ai/book/978-1-4020-2392-7
last changed	2012/09/17 21:13

_id	ecaade2024_230
id	ecaade2024_230
authors	Fekar, Hugo; Novák, Jan; Míèa, Jakub; Žigmundová, Viktória; Suleimanova, Diana; Tsikoliya, Shota; Vasko, Imrich
year	2024
title	Fabrication with Residual Wood through Scanning Optimization and Robotic Milling
source	Kontovourkis, O, Phocas, MC and Wurzer, G (eds.), Data-Driven Intelligence - Proceedings of the 42nd Conference on Education and Research in Computer Aided Architectural Design in Europe (eCAADe 2024), Nicosia, 11-13 September 2024, Volume 1, pp. 25–34
doi	https://doi.org/10.52842/conf.ecaade.2024.1.025
summary	The project deals with the use of residual wood of tree stumps and roots through scanning, optimization and robotic milling. Wood logging residue makes up to 50 percent of the trees harvested biomass. (Hakkila and Parikka 2002). Among prevailing strategies is leaving residue on site, and recovering residue for bioenergy. (Perlack and others 2005). The project explores the third strategy, using parts of the logging residue for fabrication, which may reduce the overall amount of wood logging volume. Furthermore approach aims for applying residue in its natural form and taking advantage of specific local characteristics of wood (Desch and Dinwoodie 1996). The project applies the strategy on working with stump and roots of an oak tree. Due to considerations of scale, available milling technics and available resources, chosen goal of the approach is to create a functioning chair prototype. Among the problems of the approach is the complex shape of the residue, uneven quality of wood, varying humidity and contamination with soil. After cleaning and drying, the stump is scanned and a 3D model is created. The 3D model od a stump is confronted with a 3D modelled limits of the goal typology (height, width, length, sitting surface area and overal volume of a chair) and topological optimization algorithm is used to iteratively reach the desired geometry. Unlike in established topological optimization proces, which aims for a minimal volume, the project attempts to achieve required qualities with removing minimal amount of wood. Due to geometric complexity of both stump and goal object, milling with an 6axis industrial robotic arm and a rotary table was chosen as a fabrication method. The object was clamped to the board (then connected to a rotary table) in order to provide precise location and orientation in 3D space. The milling of the object was divided in two parts, with the seating area milled in higher detail. Overall process of working with a residual wood that has potential to be both effective and present aesthetic quality based on individual characteristics of wood. Further development can integrate a generative tool which would streamline the design and fabrication proces further.
keywords	Robotic arm milling, Scanning, Residual wood
series	eCAADe
email
last changed	2024/11/17 22:05

_id	64ff
authors	Fengb, C.-X., Kusiaka, A. and Huanga, C.-C.
year	1996
title	Cost evaluation in design with form features
source	Computer-Aided Design, Vol. 28 (12) (1996) pp. 879-885
summary	Reducing the cost of a product at the design stage is more effective than at the manufacturing stage. In this paper, an attempt is presented to quantify the manufacturing cost in feature-based design. Machining form features are classified as simple and complex. The machining cost of a part depends not only on the type of form features, but also on the relationship among the features. This cost is calculated for four different cases: traditional machining, simultaneous machining, simultaneous set-up and changeover, and multiple machine tools. A manufacturing process is represented with a digraph. The feature-based evaluation of manufacturing cost is formulated as the shortest path problem, and a mathematical model as well as an algorithm are presented to determine the minimum cost design alternative.
keywords	Feature-Based Design, Design for Machining, Manufacturing Cost Evaluation
series	journal paper
last changed	2003/05/15 21:33

_id	88f4
authors	Fu, S., Bao, H. and Peng, Q.
year	1996
title	An Accelerated Rendering Algorithm for Stereoscopic Display
source	CAADRIA ‘96 [Proceedings of The First Conference on Computer Aided Architectural Design Research in Asia / ISBN 9627-75-703-9] Hong Kong (Hong Kong) 25-27 April 1996, pp. 53-61
doi	https://doi.org/10.52842/conf.caadria.1996.053
summary	With the development of the scientific visualization and the virtual environment techniques, stereo viewing systems have not been used extensively. In this paper, we present an accelerated rendering algorithm for stereoscopic display. As the difference between the left view and the right view is slight, we generate the right view by a transformation of the left view conforming to the stereo disparity. The problem of visibility change of a few polygons during the transformation is discussed and an efficient algorithm is developed for filling the holes that may arise in the right view after the transformation. This method makes fully use of the coherence between the left view and the right view. Experiments prove its efficiency.
series	CAADRIA
last changed	2022/06/07 07:50

_id	3386
authors	Gavin, L., Keuppers, S., Mottram, C. and Penn, A.
year	2001
title	Awareness Space in Distributed Social Networks
source	Proceedings of the Ninth International Conference on Computer Aided Architectural Design Futures [ISBN 0-7923-7023-6] Eindhoven, 8-11 July 2001, pp. 615-628
summary	In the real work environment we are constantly aware of the presence and activity of others. We know when people are away from their desks, whether they are doing concentrated work, or whether they are available for interaction. We use this peripheral awareness of others to guide our interactions and social behaviour. However, when teams of workers are spatially separated we lose 'awareness' information and this severely inhibits interaction and information flow. The Theatre of Work (TOWER) aims to develop a virtual space to help create a sense of social awareness and presence to support distributed working. Presence, status and activity of other people are made visible in the theatre of work and allow one to build peripheral awareness of the current activity patterns of those who we do not share space with in reality. TOWER is developing a construction set to augment the workplace with synchronous as well as asynchronous awareness. Current, synchronous activity patterns and statuses are played out in a 3D virtual space through the use of symbolic acting. The environment itself however is automatically constructed on the basis of the organisation's information resources and is in effect an information space. Location of the symbolic actor in the environment can therefore represent the focus of that person's current activity. The environment itself evolves to reflect historic patterns of information use and exchange, and becomes an asynchronous representation of the past history of the organisation. A module that records specific episodes from the synchronous event cycle as a Docudrama forms an asynchronous information resource to give a history of team work and decision taking. The TOWER environment is displayed using a number of screen based and ambient display devices. Current status and activity events are supplied to the system using a range of sensors both in the real environment and in the information systems. The methodology has been established as a two-stage process. The 3D spatial environment will be automatically constructed or generated from some aspect of the pre-existing organisational structure or its information resources or usage patterns. The methodology must be extended to provide means for that structure to grow and evolve in the light of patterns of actual user behaviour in the TOWER space. We have developed a generative algorithm that uses a cell aggregation process to transcribe the information space into a 3d space. In stage 2 that space was analysed using space syntax methods (Hillier & Hanson, 1984; Hillier 1996) to allow the properties of permeability and intelligibility to be measured, and then these fed back into the generative algorithm. Finally, these same measures have been used to evaluate the spatialised behaviour that users of the TOWER space show, and will used to feed this back into the evolution of the space. The stage of transcription from information structure to 3d space through a generative algorithm is critical since it is this stage that allows neighbourhood relations to be created that are not present in the original information structure. It is these relations that could be expected to help increase social density.
keywords	Algorithmic Form Generation, Distributed Workgroups, Space Syntax
series	CAAD Futures
email
last changed	2006/11/07 07:22

_id	1aa5
authors	Huangb, X., Gub, P. and Zernickea, R.
year	1996
title	Localization and comparison of two free-form surfaces
source	Computer-Aided Design, Vol. 28 (12) (1996) pp. 1017-1022
summary	Comparison of two free-form surfaces based on discrete data points is of paramount importance for reverse engineering. It can be used to assess the accuracy of the reconstructed surfaces and to quantify thedifference between two such surfaces. The entire process involves three main steps: data acquisition, 3D feature localization and quantitative comparison. This paper presents models and algorithms for 3D featurelocalization and quantitative comparison. Complex free-form surfaces are represented by bicubic parametric spline surfaces using discrete points. A simple yet effective pseudoinverse algorithm was developed andimplemented for localization. It consists of two iterative operations, namely, constructing a pseudo transformation matrix and point matching. A computing algorithm was developed to compare two such surfacesusing optimization techniques. Since this approach does not involve solving non-linear equations for the parameters of positions and orientations, it is fast and robust. The algorithm was implemented and testedwith several examples. It is effective and can be used in industry for sculptured surface comparison.
keywords	Free-Form Sculptured Surface, Localization, Point Matching, Surface Comparison
series	journal paper
last changed	2003/05/15 21:33

_id	ddssup9612
id	ddssup9612
authors	Kribbe, Willeke and Sanders, Frank
year	1996
title	Growth of spatial network constructions: a decision support systems oriented approach
source	Timmermans, Harry (Ed.), Third Design and Decision Support Systems in Architecture and Urban Planning - Part two: Urban Planning Proceedings (Spa, Belgium), August 18-21, 1996
summary	The paper describes a method that has been developed to be used in a process for a systematic search of alternative designs for a network configuration. In the design process we will take into account that we may not be able to implement the full configuration all at once. Logical partial configurations must be derived. The process can than also be used to investigate the expansion of (railroad) networks. The basic idea is that either the most profitable trajectories or the trajectories that contribute most to the improved quality of the configuration will be developed first. A method cannot incorporate all criteria that are relevant for the final decision simultaneously, one of the reasons being that not all criteria are suitable for a mathematical formulation. Therefore a method cannot be used to replace current legal and political procedures. However it can be considered to be part of a decision support system that could be used in a preliminary investigation preceeding such procedures. In the example presented in this paper the criteria and calculations are kept simple for illustrative purposes. However they can easily be made more complex and realistic without damaging the fundamental concepts of the search algorithm. If the system is implemented in a way that the criteria to be used in the selection process can be chosen in interaction with the decision maker (or moderator) one can truly speak of a decision support system for the project formulation phase for the construction of the physical network. In the algorithm the network is represented as a graph and the nodes connected by the network are termed centers of attraction, supply and demand.
series	DDSS
last changed	2003/08/07 16:36

_id	8bea
authors	Lipson, H. and Shpitalni, M.
year	1996
title	Optimization-based reconstruction of a 3D object from a single freehand line drawing
source	Computer-Aided Design, Vol. 28 (8) (1996) pp. 651-663
summary	This paper describes an optimization-based algorithm for reconstructing a 3D model from a single, inaccurate, 2D edge-vertex graph. The graph, which serves as input for the reconstruction process, is obtained froman inaccurate freehand sketch of a 3D wireframe object. Compared with traditional reconstruction methods based on line labelling, the proposed approach is more tolerant of faults in handling both inaccurate vertexpositioning and sketches with missing entities. Furthermore, the proposed reconstruction method supports a wide scope of general (manifold and non-manifold) objects containing flat and cylindrical faces. Sketchesof wireframe models usually include enough information to reconstruct the complete body. The optimization algorithm is discussed, and examples from a working implementation are given.
keywords	Drawing To Model, Optimization, Robustness
series	journal paper
last changed	2003/05/15 21:33

_id	62a1
authors	Maher, M.L. and Poon, J.
year	1996
title	Modelling design exploration as co-evolution
source	Microcomputers in Civil Engineering, 11:192-207
summary	Most computer-based design tools assume designers work with a well defined problem. However, this assumption has been challenged by current research. The explorative aspect of design, especially during conceptual design, is not fully addressed. This paper introduces a model for problem-design exploration, and how this model can be implemented using the genetic algorithm (GA) paradigm. The basic GA, which does not support our exploration model, evaluates individuals from a population of design solutions with an unchanged fitness function. This approach to evaluation implements search with a prefixed goal. Modifications to the basic GA are required to support exploration. Two approaches to implement a co-evolving GA are presented and discussed in this paper: one in which the fitness function is represented within the genotype, and a second in which the fitness function is modelled as a separately evolving population of genotypes.
series	journal paper
email
last changed	2003/04/23 15:50

_id	1162
authors	Malkawi, Ali and Jabi, Wassim
year	1996
title	Integrating Shadow Casting Methodology and Thermal Simulation
source	Proceedings of the Solar ‘96 Conference. Asheville, North Carolina: American Solar Energy Society, 1996, pp. 271-276
summary	This paper describes an experiment that integrates shadow casting methodology and thermal simulation algorithms developed by the authors. The 3D shadow procedures use a polyhedral representation of solids within a Cartesian space that allows for accurate casting of shadows. The algorithm is also capable of calculating surface areas of polygonal shadows of any arbitrary shape and size. The thermal simulation algorithms – using the Transfer Function Method (TFM) – incorporate the shaded area calculations to better predict solar heat gain from glazing based on transmitted, absorbed, and conducted cooling loads. The paper describes the use of a 3D computer model to illustrate the impact of the pattern and area of shading on the visual and thermal properties of building apertures. The paper discusses the objectives of this experiment, the algorithms used, and their integration. Conclusions and findings are drawn.
keywords	Shadow Casting Algorithms Energey Thermal Simulation
series	other
email
last changed	2002/03/05 19:51

_id	c363
authors	Pieglb, Les and Tillera, Wayne
year	1996
title	Algorithm for approximate NURBS skinning
source	Computer-Aided Design, Vol. 28 (9) (1996) pp. 699-706
summary	An algorithm for approximate skinning through cross-sectionalNURBS curves is presented. The method eliminates the problem of dealing with huge amounts of control points obtained during the curvecompatability process. It also allows the designer to specify large numbers of cross-sections and approximately fit a smooth surface to these curves to any given tolerance. Depending on the tolerances used, up to99% of the control points can be eliminated.
keywords	NURBS, Surface Skinning, Curves and Surfaces, Algorithms
series	journal paper
last changed	2003/05/15 21:33

_id	acadia07_284
id	acadia07_284
authors	Robinson, Kirsten; Gorbet, Robert; Beesley, Philip
year	2007
title	Evolving Cooperative Behaviour in a Reflexive Membrane
source	Expanding Bodies: Art • Cities• Environment [Proceedings of the 27th Annual Conference of the Association for Computer Aided Design in Architecture / ISBN 978-0-9780978-6-8] Halifax (Nova Scotia) 1-7 October 2007, 284-293
doi	https://doi.org/10.52842/conf.acadia.2007.284
summary	This paper describes the integration of machine intelligence into an immersive architectural sculpture that interacts dynamically with users and the environment. The system is conceived to function as an architectural envelope that might transfer air using a distributed array of components. The sculpture includes a large array of interconnected miniature structural and kinetic elements, each with local sensing, actuation, and machine intelligence. We demonstrate a model in which these autonomous, interconnected agents develop cooperative behaviour to maximize airflow. Agents have access to sensory data about their local environment and ‘learn’ to move air through the working of a genetic algorithm. Introducing distributed and responsive machine intelligence builds on work done on evolving embodied intelligence (Floreano et al. 2004) and architectural ‘geotextile’ sculptures by Philip Beesley and collaborators (Beesley et al. 1996-2006). The paper contributes to the general field of interactive art by demonstrating an application of machine intelligence as a design method. The objective is the development of coherent distributed kinetic building envelopes with environmental control functions. A cultural context is included, discussing dynamic paradigms in responsive architecture.
series	ACADIA
type	normal paper
email
last changed	2022/06/07 08:00

_id	4040
authors	Smith, I., Stalker, R. and Lottaz, C.
year	1996
title	Creating design objects from cases for interactive spatial composition
source	Artificial Intelligence in Design ‚96, eds. J. S. Gero and F. Sudweeks, 97 - 116. Dordrecht: Kluwer Academic
summary	This paper describes IDIOM, a system for composing layouts using cases. Layouts are interactively composed by users rather than automatically generated as has been proposed by previous research. The design is incrementally parameterized as cases are added and therefore, case adaptation, user interpretation and model activation can occur at any stage. IDIOM supports designers through reducing constraint complexity and through managing design preferences, thereby restraining proposed solutions and further adaptation within globally feasible design spaces. Improvements to the algorithm over previous implementations have increased reliability. In general, designers, who currently carry out spatial composition tasks using standard drawing tools, have reacted favourably to the system, providing useful feedback for further work.
series	journal paper
last changed	2003/04/23 15:14

_id	2b76
authors	Winkenbach, G. and Salesin, D.H.
year	1996
title	Rendering free-form surfaces in pen and ink
source	Computer Graphics Proceedings, Annual Conference Series 1996. ACM SIGGRAPH, pp. 469-476.
summary	This paper presents new algorithms and techniques for rendering parametric free-form surfaces in pen and ink. In particular, we introduce the idea of "controlled-density hatching" for conveying tone, texture, and shape. The fine control over tone this method provides allows the use of traditional texture mapping techniques for specifying the tone of pen-and-ink illustrations.We also show how a planar map, a data structure central to our rendering algorithm, can be constructed from parametric surfaces, and used for clipping strokes and generating outlines. Finally, we show how curved shadows can be cast onto curved objects for this style of illustration.
series	other
last changed	2003/04/23 15:50

_id	a9ca
authors	Abadi Abbo, Isaac
year	1996
title	EFFECTIVENESS OF MODELS
source	Full-Scale Modeling in the Age of Virtual Reality [6th EFA-Conference Proceedings]
summary	Architects use many types of models to simulate space either in their design process or as final specifications for building them. These models have been proved useful or effective for specific purposes. This paper evaluates architectural models in terms of five effectiveness components: time of development, cost, complexity, variables simulated and ecological validity. This series of models, used regularly in architecture, are analysed to finally produce a matrix that shows the effectiveness of the different models for specific purposes in architectural design, research and education. Special emphasis is given to three specific models: 1/10 scale, full-scale and computer generated.
keywords	Model Simulation, Real Environments
series	other
type	normal paper
more	http://info.tuwien.ac.at/efa/
last changed	2016/02/17 13:47

_id	ascaad2004_paper11
id	ascaad2004_paper11
authors	Abdelfattah, Hesham Khairy and Ali A. Raouf
year	2004
title	No More Fear or Doubt: Electronic Architecture in Architectural Education
source	eDesign in Architecture: ASCAAD's First International Conference on Computer Aided Architectural Design, 7-9 December 2004, KFUPM, Saudi Arabia
summary	Operating electronic and Internet worked tools for Architectural education is an important, and merely a prerequisite step toward creating powerful tele-collabortion and tele-research in our Architectural studios. The design studio, as physical place and pedagogical method, is the core of architectural education. The Carnegie Endowment report on architectural education, published in 1996, identified a comparably central role for studios in schools today. Advances in CAD and visualization, combined with technologies to communicate images, data, and “live” action, now enable virtual dimensions of studio experience. Students no longer need to gather at the same time and place to tackle the same design problem. Critics can comment over the network or by e-mail, and distinguished jurors can make virtual visits without being in the same room as the pin-up—if there is a pin-up (or a room). Virtual design studios (VDS) have the potential to support collaboration over competition, diversify student experiences, and redistribute the intellectual resources of architectural education across geographic and socioeconomic divisions. The challenge is to predict whether VDS will isolate students from a sense of place and materiality, or if it will provide future architects the tools to reconcile communication environments and physical space.
series	ASCAAD
email
last changed	2007/04/08 19:47

For more results click below: