Cumincad : CUMINCAD Papers : Search Results

CumInCAD is a Cumulative Index about publications in Computer Aided Architectural Design
supported by the sibling associations ACADIA, CAADRIA, eCAADe, SIGraDi, ASCAAD and CAAD futures

PDF papers
References

Hits 1 to 20 of 505

Reformat results as: short short into frame detailed detailed into frame

_id	6f10
authors	Petric, J., Maver, T.W., Conti, G. and Ucelli, G.
year	2002
title	Virtual Reality in the Service of User Participation
source	Distributing Knowledge in Building. Proceedings of CIB W78 Conference (Ed. K Agger et al), Aarhus, 217-224
summary	The normal application of Virtual Reality is to the simulation of environments which are in some way special - remote, hazardous or purely imaginary. This paper describes research and development work which changes the paradigm by simulating perfectly ordinary buildings for special people. Some of the population have some form of physical impairment - a proportion which is likely to rise in line with an ageing population. New legislation, such as the UK Disability Discrimination Act places additional responsibility on building owners to ensure adequate access for people with an impairment and this in turn will place additional responsibility on the architect. Current methods of auditing access for new building are primitive and require the auditor to interpret plans/sections of the proposed building against a checklist of requirements specific to the special need. This paper reports on progress in the use of an immersive VR facility to simulate access to buildings for two broad classes of user: i) those with a mobility impairment ii) those with a visual impairment In the former case, a wheelchair motion platform has been designed which allows the wheelchair user to navigate the virtual building; a brake and motor connected to the rollers on which the wheelchair sits facilitate the effects of slope and surface resistance.
series	other
type	normal paper
email
last changed	2015/02/20 11:24

_id	ee65
authors	Bourdakis, Vassilis and Charitos, Dimitris
year	2002
title	Teaching Virtual Environment Design
source	Connecting the Real and the Virtual - design e-ducation [20th eCAADe Conference Proceedings / ISBN 0-9541183-0-8] Warsaw (Poland) 18-20 September 2002, pp. 42-49
doi	https://doi.org/10.52842/conf.ecaade.2002.042
summary	In a previous paper, the authors considered the design and development of virtual environments (VEs) pointing out the need for a new direction within architectural education, leading towards a generation of VE architects. It was suggested that there is an urgent need for educating practitioners who will contribute to the design of 3D content for multimedia and virtual reality applications. This paper focuses on the application of these principles and ideas into the structure and methodology of three VE design courses, taught by the authors. These courses are by no means suggested as exhaustive examples of teaching this subject. They are seen as preliminary approaches, adapting to the educational context they are integrated within. Bearing in mind the problems relating to teaching large numbers of students with a design studio approach, difficult concepts, resources availability, fighting misconceptions, techno-phobia the following areas are discussed in the hope that they will contribute to VE design curricula in the near future.
series	eCAADe
email
last changed	2022/06/07 07:54

_id	1389
authors	Bustos, Gabriela L. and Burgos, Iván P.
year	2002
title	Desarrollo y Aplicabilidad de Menús Virtuales en VRML [Architectonic Development and Applicability of Virtual Menus in VRML]
source	SIGraDi 2002 - [Proceedings of the 6th Iberoamerican Congress of Digital Graphics] Caracas (Venezuela) 27-29 november 2002, pp. 199-202
summary	The Virtual Reality Modeling Language (VRML), has allowed extend all of its resources and possibilities for Architectural Applications under the same Virtual Reality’s technology platform. In order to take advantages of its possibilities, this resource focus on exposes the development and application of virtual menus in VRML and Java Script as a first step for the creation of Synthetic Environment Laboratory in the faculty of Architecture and Design of University of Zulia, Venezuela. It presents in short, how algorithms were defined to design the menus, the use of a program in Visual Basic that permit addition of virtual menus toany WRL file, without any programming approach, as well as specific samples of applicability of the menus developed in a VRMLenvironment and how they are included in a methodological model of architectural design.
keywords	virtual reality, synthetic environments, architectural design, inmersive projection systems.
series	SIGRADI
email
last changed	2016/03/10 09:47

_id	ddssar0207
id	ddssar0207
authors	Conti, G. and Ucelli, G.
year	2002
title	A Java3D Tool for Real-Time Collaboration in a Virtual Reality CAADEnvironment
source	Timmermans, Harry (Ed.), Sixth Design and Decision Support Systems in Architecture and Urban Planning - Part one: Architecture Proceedings Avegoor, the Netherlands), 2002
summary	Today the development of network-based virtual communities and the use of avatars have brought a new level of complexity to the meaning of virtuality, providing the technology for remote presence and collaborative experiences. In this project the intention was to pursue this articulated vision of VR in order to assist the design profession during the early stages of the design process. The objective was to provide a tool that is capable of creating 3D shapes in a shared VR environment, thus allowing thedesign and its evolution to be shared. The use of the Java programming language was a natural choice for this project. Because of Java’s performance scalability and hardware independence the concept ofCAAD has been extended, making it possible to create a VR environment that can co-exist between high-end supercomputers and standard PCs. The project is currently being tested using PCs and an SGI system running a Reality Centre. The research reported in this paper describes the architecture and application of software that aims to increase the opportunity for collaboration within virtual worlds and enable effective and transparent information exchange.
series	DDSS
last changed	2003/08/07 16:36

_id	ddssar0211
id	ddssar0211
authors	Fröst, Peter
year	2002
title	Interactive Tools for Collaborative Architectural Design
source	Timmermans, Harry (Ed.), Sixth Design and Decision Support Systems in Architecture and Urban Planning - Part one: Architecture Proceedings Avegoor, the Netherlands), 2002
summary	Today’s rapidly changing society is continuously developing towards an increased demand for multistakeholder knowledge and influence in the architectural planning and design process. Accordingly, we are working with developing and setting up a partner engaged collaborative design process. It includes active collaboration between users, external partners and designers, and visualizations in conceptual design and scenario building. My research is focusing on integrating visualization technology in theseprocesses by application of digital tools. We have developed a working prototype for an interactive design tool. The prototype is an extremely “easy to use” digital modeling tool called “ForeSite Designer.” With this tool one builds one’s own spatial environment with elements on a 2D surface.With one command the 2D layout is exported to a lit-up 3D/Virtual Reality world in the computer game “Half-Life”. ForeSite Designer has lately been used in a series of workshops together with external users. In these processes ForeSite Designer has played a crucial role as an arena of building spatially arranged concepts of future environments. The results show that it works, and, importantly, promotes a collaborative engagement among the users.
series	DDSS
last changed	2003/08/07 16:36

_id	ga0216
id	ga0216
authors	Manzolli, J. and Lindner, F. and Carrilho ,F.
year	2002
title	Constructing Distributed Fretted Instruments for the Web
source	International Conference on Generative Art
summary	In this article, we present a new computer based music instrument for distributed performance on the Web. It was named “Cordas Virtuais” and we took advantage of the recent Java2 implementation to create a general model for fretted-string instruments using class abstractions. There is a heavy usage of JAVA Objected Oriented inheritance to encapsulate gestures derived from fretted string instruments using parameters such as string tuning, group of strings, hand gestures, rhythmic patterns, fingering and alike, that carry each a set of attributes and properties. We call this kind of new musical application as Distributed Musical Instrument (DMI). As an applet, Cordas runs in any browser supporting the current Java Virtual Machine (JVM) across the Web. We describe the concept of PlayStyle that was created to define styles of fingering on the strings. In the implementation we have two class-groups: the left hand and the right hand gestures. The left-hand classes control pitch changes or chords, and a right hand control the rhythm, dynamics, micro-rhythms and rhythmic patterns. A Co-ordination Matrix controls real time changes on left-hand movements. This matrix generates chord orbits that are equivalent to the traditional chord cadences. Finally, to show the potential of Cordas, we presented four musical examples in which a set of fretted instruments varying from the Classical Guitar to the Chinese Pipa were simulated.
keywords	MIDI, Java2, interactive music, fretted instruments, real time
series	other
email
more	http://www.generativeart.com/
last changed	2003/08/07 17:25

_id	c7e9
authors	Maver, T.W.
year	2002
title	Predicting the Past, Remembering the Future
source	SIGraDi 2002 - [Proceedings of the 6th Iberoamerican Congress of Digital Graphics] Caracas (Venezuela) 27-29 november 2002, pp. 2-3
summary	Charlas Magistrales 2There never has been such an exciting moment in time in the extraordinary 30 year history of our subject area, as NOW,when the philosophical theoretical and practical issues of virtuality are taking centre stage.The PastThere have, of course, been other defining moments during these exciting 30 years:• the first algorithms for generating building layouts (circa 1965).• the first use of Computer graphics for building appraisal (circa 1966).• the first integrated package for building performance appraisal (circa 1972).• the first computer generated perspective drawings (circa 1973).• the first robust drafting systems (circa 1975).• the first dynamic energy models (circa 1982).• the first photorealistic colour imaging (circa 1986).• the first animations (circa 1988)• the first multimedia systems (circa 1995), and• the first convincing demonstrations of virtual reality (circa 1996).Whereas the CAAD community has been hugely inventive in the development of ICT applications to building design, it hasbeen woefully remiss in its attempts to evaluate the contribution of those developments to the quality of the built environmentor to the efficiency of the design process. In the absence of any real evidence, one can only conjecture regarding the realbenefits which fall, it is suggested, under the following headings:• Verisimilitude: The extraordinary quality of still and animated images of the formal qualities of the interiors and exteriorsof individual buildings and of whole neighborhoods must surely give great comfort to practitioners and their clients thatwhat is intended, formally, is what will be delivered, i.e. WYSIWYG - what you see is what you get.• Sustainability: The power of «first-principle» models of the dynamic energetic behaviour of buildings in response tochanging diurnal and seasonal conditions has the potential to save millions of dollars and dramatically to reduce thedamaging environmental pollution created by badly designed and managed buildings.• Productivity: CAD is now a multi-billion dollar business which offers design decision support systems which operate,effectively, across continents, time-zones, professions and companies.• Communication: Multi-media technology - cheap to deliver but high in value - is changing the way in which we canexplain and understand the past and, envisage and anticipate the future; virtual past and virtual future!MacromyopiaThe late John Lansdown offered the view, in his wonderfully prophetic way, that ...”the future will be just like the past, onlymore so...”So what can we expect the extraordinary trajectory of our subject area to be?To have any chance of being accurate we have to have an understanding of the phenomenon of macromyopia: thephenomenon exhibitted by society of greatly exaggerating the immediate short-term impact of new technologies (particularlythe information technologies) but, more importantly, seriously underestimating their sustained long-term impacts - socially,economically and intellectually . Examples of flawed predictions regarding the the future application of information technologiesinclude:• The British Government in 1880 declined to support the idea of a national telephonic system, backed by the argumentthat there were sufficient small boys in the countryside to run with messages.• Alexander Bell was modest enough to say that: «I am not boasting or exaggerating but I believe, one day, there will bea telephone in every American city».• Tom Watson, in 1943 said: «I think there is a world market for about 5 computers».• In 1977, Ken Olssop of Digital said: «There is no reason for any individuals to have a computer in their home».The FutureJust as the ascent of woman/man-kind can be attributed to her/his capacity to discover amplifiers of the modest humancapability, so we shall discover how best to exploit our most important amplifier - that of the intellect. The more we know themore we can figure; the more we can figure the more we understand; the more we understand the more we can appraise;the more we can appraise the more we can decide; the more we can decide the more we can act; the more we can act themore we can shape; and the more we can shape, the better the chance that we can leave for future generations a trulysustainable built environment which is fit-for-purpose, cost-beneficial, environmentally friendly and culturally significactCentral to this aspiration will be our understanding of the relationship between real and virtual worlds and how to moveeffortlessly between them. We need to be able to design, from within the virtual world, environments which may be real ormay remain virtual or, perhaps, be part real and part virtual.What is certain is that the next 30 years will be every bit as exciting and challenging as the first 30 years.
series	SIGRADI
email
last changed	2016/03/10 09:55

_id	acadia16_140
id	acadia16_140
authors	Nejur, Andrei; Steinfeld, Kyle
year	2016
title	Ivy: Bringing a Weighted-Mesh Representations to Bear on Generative Architectural Design Applications
source	ACADIA // 2016: POSTHUMAN FRONTIERS: Data, Designers, and Cognitive Machines [Proceedings of the 36th Annual Conference of the Association for Computer Aided Design in Architecture (ACADIA) ISBN 978-0-692-77095-5] Ann Arbor 27-29 October, 2016, pp. 140-151
doi	https://doi.org/10.52842/conf.acadia.2016.140
summary	Mesh segmentation has become an important and well-researched topic in computational geometry in recent years (Agathos et al. 2008). As a result, a number of new approaches have been developed that have led to innovations in a diverse set of problems in computer graphics (CG) (Sharmir 2008). Specifically, a range of effective methods for the division of a mesh have recently been proposed, including by K-means (Shlafman et al. 2002), graph cuts (Golovinskiy and Funkhouser 2008; Katz and Tal 2003), hierarchical clustering (Garland et al. 2001; Gelfand and Guibas 2004; Golovinskiy and Funkhouser 2008), primitive fitting (Athene et al. 2004), random walks (Lai et al.), core extraction (Katz et al.) tubular multi-scale analysis (Mortara et al. 2004), spectral clustering (Liu and Zhang 2004), and critical point analysis (Lin et al. 20070, all of which depend upon a weighted graph representation, typically the dual of a given mesh (Sharmir 2008). While these approaches have been proven effective within the narrowly defined domains of application for which they have been developed (Chen 2009), they have not been brought to bear on wider classes of problems in fields outside of CG, specifically on problems relevant to generative architectural design. Given the widespread use of meshes and the utility of segmentation in GAD, by surveying the relevant and recently matured approaches to mesh segmentation in CG that share a common representation of the mesh dual, this paper identifies and takes steps to address a heretofore unrealized transfer of technology that would resolve a missed opportunity for both subject areas. Meshes are often employed by architectural designers for purposes that are distinct from and present a unique set of requirements in relation to similar applications that have enjoyed more focused study in computer science. This paper presents a survey of similar applications, including thin-sheet fabrication (Mitani and Suzuki 2004), rendering optimization (Garland et al. 2001), 3D mesh compression (Taubin et al. 1998), morphin (Shapira et al. 2008) and mesh simplification (Kalvin and Taylor 1996), and distinguish the requirements of these applications from those presented by GAD, including non-refinement in advance of the constraining of mesh geometry to planar-quad faces, and the ability to address a diversity of mesh features that may or may not be preserved. Following this survey of existing approaches and unmet needs, the authors assert that if a generalized framework for working with graph representations of meshes is developed, allowing for the interactive adjustment of edge weights, then the recent developments in mesh segmentation may be better brought to bear on GAD problems. This paper presents work toward the development of just such a framework, implemented as a plug-in for the visual programming environment Grasshopper.
keywords	tool-building, design simulation, fabrication, computation, megalith
series	ACADIA
type	paper
email
last changed	2022/06/07 07:58

_id	e81e
authors	Petric, J., Ucelli, G. and Conti, G.
year	2002
title	Participatory Design in Collaborative Virtual Environments
source	SIGraDi 2002 - [Proceedings of the 6th Iberoamerican Congress of Digital Graphics] Caracas (Venezuela) 27-29 november 2002, pp. 159-162
summary	This paper re-establishes the theoretical framework for participatory design evolved in the late sixties and early seventies as part of the movement towards a more explicit design methodology and attempts an explanation of why the concept failed to gain commitment from the architectural and urban design professionals. The issue of user participation in the processes of building and urban design is enjoying renewed attention following its relative neglect over the last 20 years due, in large measure, to significant advances in emerging information technologies, particularly multimedia, virtual reality and internettechnologies. This paper then gives an account of two significant and relevant developments in the evolution of the application of informationtechnologies with which the authors have been engaged. These are:a responsive and interactive interface to wholly immersive and realistic virtual reality representations of proposed buildings and urban neighbourhoods. an intuitive and platform-independent VR modelling environment allowing collaborative evolution of the scheme from withinthe virtual world. The efficacy of these IT developments is tested in the context of a design exercise in which three designers, from distributedlocations and using different computer platforms, collaboratively design an Information Centre from within the virtual world.
series	SIGRADI
email
last changed	2016/03/10 09:57

_id	f1a5
authors	Petric, J., Ucelli, G. and Ucelli, G.
year	2002
title	Real Teaching and Learning through Virtual Reality
source	Connecting the Real and the Virtual - design e-ducation [20th eCAADe Conference Proceedings / ISBN 0-9541183-0-8] Warsaw (Poland) 18-20 September 2002, pp. 72-79
doi	https://doi.org/10.52842/conf.ecaade.2002.072
summary	This paper addresses an articulated vision of Virtual Reality which lends itself to design collaboration in teaching, learning and communication of architectural design ideas among students, design professionals and client body during the early stages of the design process. Virtual Reality (VR) has already acquired a new degree of complexity through development of network-based virtual communities and the use of avatars. The intrinsic quality of VR technology is to support collaborative design experience. The design tools developed for this experiment are capable of creating 3D objects in a shared VR environment, thus allowing the design and its evolution to be shared. The choice of programming language (JavaTM) reflects the desire to achieve scalability and hardware independence, which in turn allows for creation of a VR environment that can co-exist between high-end supercomputers and standard PCs. The prototype design environment was tested using PC workstations and an SGI system running a Reality Centre. The research and teaching/learning experience in the collaborative design environment reported in this paper describe the development and application of software that aims to increase the opportunity for architects to collaborate within virtual worlds which enable effective and transparent information exchange.
series	eCAADe
email
last changed	2022/06/07 08:00

_id	bff9
authors	Proctor, George (Ed.)
year	2002
title	ACADIA 2002 [Conference Proceedings]
source	Proceedings of the 2002 Annual Conference of the Association for Computer Aided Design In Architecture / ISBN 1-880250-11-X / Pomona (California) 24-27 October 2002, 446 p.
doi	https://doi.org/10.52842/conf.acadia.2002
summary	The 2002 ACADIA conference finds digital tec_nology ubiquitous as the Association for Computer Aided Design in Architecture moves into its third decade. The organization of ACADIA is on the threshold of restating its mission. After 20 years, many of the organization’s initial objectives have been achieved. ACADIA members have been instrumental in the development of design software, and in bringing computers and digital technology into architectural practice and design school curriculum. At first, ACADIAns faced the debate over the appropriateness and utility of digital technology in the disciplines of architecture, planning and building science. Today the use of computers and information technology is widely accepted by architects and CAAD and digital technology have brought profound change to design practice. The debate in ACADIA has long since moved from "should we use this technology" to "how", "for what" and "why". Now that many practitioners, learning institutions and professional organizations have taken up the call, ACADIA must restate its mission, if it wishes to remain “distinct”. This does not mean that the work of ACADIA is complete. Much remains to be done and much more needs to be improved. ACADIA’s Mission Statement places particular focus on “education and the software, hardware and pedagogy involved in education.” And “(t)he organization is also committed to the research and development of computer aides that enhance design creativity, and that aim at contributing to the construction of humane physical environments.” These are the areas that continue to evolve, grow and provide for ACADIA’s continued relevance. The ACADIA 2002 conference theme reflects the state of digital technology’s application to the discipline, as much as it refers to ACADIA’s future. With the general acceptance of digital technology and CAAD, we have arrived at a place where the work of great interest and relevance lies in the space between what is digital and what is analog. The environments of real space and cyberspace have in a very short time become so intertwined that the space between real and virtual (not to be confused with reality and fantasy) is becoming indistinguishable. You cannot eat, travel, use public utilities, bank, shop, vacation or recreate without at the very least coming into contact with or passing through information space. The landscape between these two environments has become a cultural phenomenon for those societies with access to the Internet and information networks. And while the computer and World Wide Web have empowered individuals, the collective impact of the technology holds all the potential and problems that similarly emerged in other technology induced landscapes. Consider this last point in the context of ACADIA’s stated mission to “enhance design creativity while contributing to the construction of humane physical environments.” And you can see why many of the 260 initial submissions to this conference were in the area of design artifacts and design methodology, providing evidence that ACADIA’s mission remains relevant and in accord with the trends of research and professional creative activity.
series	ACADIA
email
last changed	2022/06/07 07:49

_id	1fda
authors	Rashid, Hani and Couture, Lise Anne
year	2002
title	Virtual Architecture – Real Space
source	CAADRIA 2002 [Proceedings of the 7th International Conference on Computer Aided Architectural Design Research in Asia / ISBN 983-2473-42-X] Cyberjaya (Malaysia) 18–20 April 2002, pp. 005-8
doi	https://doi.org/10.52842/conf.caadria.2002.005
summary	We are in the very early stages of a digital revolution whose direction we will not be certain of for sometime, much in the same way that Enlightenment-era architects, theologians, and thinkers did not quite comprehend the profound changes taking place in their own time. Today’s digital technologies are having profound effects on many different aspects of our contemporary understanding from the human genome to the mapping of the cosmos. Digital manipulations that use virtual-reality technologies form a major part of this revolution. As architects we are responding in a number of ways, by conceiving of entirely new geometric principles, new methodologies, and entirely novel approaches to representation beyond perspectival geometry.
series	CAADRIA
email
more	http://www.asymptote.net
last changed	2022/06/07 08:00

_id	6b70
authors	Af Klercker, Jonas and Pittioni, Gernot
year	2002
title	Architect and Structural Engineer in interactive design
source	Connecting the Real and the Virtual - design e-ducation [20th eCAADe Conference Proceedings / ISBN 0-9541183-0-8] Warsaw (Poland) 18-20 September 2002, pp. 386-389
doi	https://doi.org/10.52842/conf.ecaade.2002.386
summary	We are convinced that an interactive design process involving engineers and architects will create values to a project. Looking back there have been some obstacles, like a week’s time for exchange of drawings with traditional postal services; manual calculation methods, which could not be spoiled on loose grounds like architect’s sketches; different media – architect’s drawings and engineer’s numbers in tables; attitudes and traditional roles, implemented already in education. Today most of these obstacles can be overcome and we have made a test. We have used ArchiCad by Graphisoft and FEM-design by SKANSKA IT Solutions to test to make an interactive design. Our conclusions are that exchange of information, drawings and other documents is more or less routine in praxis, and it works almost instantly. Computers make calculation faster and easier for the engineer. Though we would wish to have software which manages to do more rapid estimations. Even simulations such as of loads on a structure are practically possible. By using model based CAD the data can be used for transferring quantities for calculations as well as visualization of the design as a platform for collaborate analysis. The technique is developed and usable but to gain acceptance and make use of it is also a matter of attitudes and of application activities in education.
series	eCAADe
type	normal paper
email
last changed	2022/06/07 07:54

_id	ddssar0203
id	ddssar0203
authors	Alkass, Sabah and Jrade, Ahmad
year	2002
title	A Web-Based Virtual Reality Model for Preliminary Estimates of Hi-Rise Building Projects
source	Timmermans, Harry (Ed.), Sixth Design and Decision Support Systems in Architecture and Urban Planning - Part one: Architecture Proceedings Avegoor, the Netherlands), 2002
summary	Cost estimating of a construction project at its early stage is considered to be very important task since it will be used as a base to commit or otherwise not to commit funds to that project. Preparation of a reliableand realistic preliminary estimate to aid the decision makers to commit funds for a specific project is a complicated assignment. Traditional methods and operations produced unsatisfactory aid due to lack ofaccuracy especially in the pre-design stage of a project. This participates in the increase of percentage of bankruptcy in the construction industry, which has dramatically climbed up and ranked as 15 percent of thewhole bankruptcies claimed in Canada (Statistic Canada 1998). This paper presents a methodology for developing and a Web-based model to automate preliminary cost estimates for hi-rise buildings. This is achieved by integrating a database with design drawings in a Virtual Reality (VR) environment. The model will automatically generate preliminary estimates after modifying a 3D CAD drawing. It provides the user the option to visualize and simulate the drawing and its cost data through VR environment. Having done that, it will allow owners, architects and cost engineers to view a constructed building project, change its geometric objects and shapes, and accordingly generate a new conceptual cost estimate.
series	DDSS
last changed	2003/11/21 15:15

_id	1d66
authors	Asanowicz, Aleksander
year	2002
title	Hybrid Design Environment
source	Connecting the Real and the Virtual - design e-ducation [20th eCAADe Conference Proceedings / ISBN 0-9541183-0-8] Warsaw (Poland) 18-20 September 2002, pp. 572-576
doi	https://doi.org/10.52842/conf.ecaade.2002.572
summary	This paper discusses some preliminary ideas concerning new design environment or environment of designing. Main thesis of this paper is that process of creation and perception of architecture proceed between Real and Virtual. Architecture is created by analog and/or digital media. A the result we have the multitude and diversity of spaces and tools. Defining these terms is important for understanding a new process of design and a new space of designing. It gives us possibilities to create the new design environment, in which creation of architectural form may be considered as an integrated process connecting the analog, the digital, the real and the virtual. Architectural space, as we know it from physical environments, is supplemented by a virtual space. Physical, architectural and virtual spaces share very similar features in simulation. In virtual models, the boundary between the representation of physical sites and imaginary, virtual sites is vanishing rapidly, resulting in a new reality.
series	eCAADe
email
last changed	2022/06/07 07:54

_id	5422
authors	Barría, H., Lagos, R. and Munoz, Chr.
year	2002
title	The Inter-Media Space
source	Connecting the Real and the Virtual - design e-ducation [20th eCAADe Conference Proceedings / ISBN 0-9541183-0-8] Warsaw (Poland) 18-20 September 2002, pp. 584-587
doi	https://doi.org/10.52842/conf.ecaade.2002.584
summary	This paper explores the juxtaposition between architectonic space and virtual environments. It establishes the hypothesis that the intersection of virtual environments with our common life causes a break-up of time and space. Virtual environments are the last and most integral part of the technological revolution, becoming a parallel world, an unlimited extension of our limited world. The spatial and temporal juxtaposition of these two realities creates a new reality of being “inbetween”, it reveals the “inter-media”. This “inter-media” reality is an issue for architecture of our time, and it still lacks of responses.
series	eCAADe
email
last changed	2022/06/07 07:54

_id	27a9
authors	Bille, Pia
year	2002
title	From CAD to Communication
source	Connecting the Real and the Virtual - design e-ducation [20th eCAADe Conference Proceedings / ISBN 0-9541183-0-8] Warsaw (Poland) 18-20 September 2002, pp. 156-159
doi	https://doi.org/10.52842/conf.ecaade.2002.156
summary	Establishment of the physical infrastructure for a digital school of architecture has been perceived as the main difficulty for taking advantage of IT in the curriculum. Having reached that point shows other obstacles to overcome. A scenario describes how the digital studio works and how the concept of IT in the curriculum changes. The paper ends with a discussion of 5 IT interrelated disciplines: tool, application, method, communication and collaboration.
series	eCAADe
email
last changed	2022/06/07 07:54

_id	c1f5
authors	Blaszczyszyn, Maciej
year	2002
title	Day-to-day Reality of Web-based Collaboration - Tools among European Architect Professionals
source	Connecting the Real and the Virtual - design e-ducation [20th eCAADe Conference Proceedings / ISBN 0-9541183-0-8] Warsaw (Poland) 18-20 September 2002, pp. 110-113
doi	https://doi.org/10.52842/conf.ecaade.2002.110
summary	On behalf of phenomenal advantages of project extranet technology You can believe in improving communication among professionals in design and construction industry. But until now, the reality appears not as good. It is technological irony, as evidenced in below presented survey, that advanced solutions for a better collaboration may set up unbreakable barriers. Therefore knowledge of everyday reality in the field of webbased collaboration tools use is critical to all participants of this process, commercial as well academic ones. It is especially important to all European professionals, who are aware of consequences of extending in nearest future borders of European Union, the second biggest market in the world.
series	eCAADe
email
last changed	2022/06/07 07:52

_id	eabb
authors	Boeykens, St. Geebelen, B. and Neuckermans, H.
year	2002
title	Design phase transitions in object-oriented modeling of architecture
source	Connecting the Real and the Virtual - design e-ducation [20th eCAADe Conference Proceedings / ISBN 0-9541183-0-8] Warsaw (Poland) 18-20 September 2002, pp. 310-313
doi	https://doi.org/10.52842/conf.ecaade.2002.310
summary	The project IDEA+ aims to develop an “Integrated Design Environment for Architecture”. Its goal is providing a tool for the designer-architect that can be of assistance in the early-design phases. It should provide the possibility to perform tests (like heat or cost calculations) and simple simulations in the different (early) design phases, without the need for a fully detailed design or remodeling in a different application. The test for daylighting is already in development (Geebelen, to be published). The conceptual foundation for this design environment has been laid out in a scheme in which different design phases and scales are defined, together with appropriate tests at the different levels (Neuckermans, 1992). It is a translation of the “designerly” way of thinking of the architect (Cross, 1982). This conceptual model has been translated into a “Core Object Model” (Hendricx, 2000), which defines a structured object model to describe the necessary building model. These developments form the theoretical basis for the implementation of IDEA+ (both the data structure & prototype software), which is currently in progress. The research project addresses some issues, which are at the forefront of the architect’s interest while designing with CAAD. These are treated from the point of view of a practicing architect.
series	eCAADe
email
last changed	2022/06/07 07:52

_id	3d67
authors	Breen, J., Nottrot, R. and Stellingwerff, M.
year	2002
title	Relating to the ‘real’ Perceptions of Computer Aided and Physical Modelling
source	Connecting the Real and the Virtual - design e-ducation [20th eCAADe Conference Proceedings / ISBN 0-9541183-0-8] Warsaw (Poland) 18-20 September 2002, pp. 134-138
doi	https://doi.org/10.52842/conf.ecaade.2002.134
summary	Designing - giving form to new objects or environments - is largely a question of anticipating the workings of spatial and material environments, which can become ‘reality’ only by being built. Until ‘realized’ a design is essentially a figment of the designer’s imagination, although his or her ideas may be laid down and conveyed to others via specialized design media. In this way impressions of the design may be shared with clients, colleagues or other ‘actors’ in the design process. Such products of the designer’s imaging process can be relatively abstract or begin to approach - future - reality. Form & Media research can be ‘revealing’, stimulating insights concerning preferences, working processes and the effects of products of the designer’s imagination. In the past ten years we have gained considerable practical experience with both virtual and tangible (scale) models. We have compared different techniques in conference workshops, within educational settings and in our Form & Media research laboratory. The research projects ranged from the development of practical techniques and working methods to protocol analyses of designing architects. This contribution draws comparisons between different computer aided modelling techniques, with an indication of their perspectives, making use of the experience gained from various experiments in an educational context, and will highlight the potentials for different combinations of digital and physical modelling techniques.
series	eCAADe
email
last changed	2022/06/07 07:54

For more results click below: