Cumincad : CUMINCAD Papers : Search Results

CumInCAD is a Cumulative Index about publications in Computer Aided Architectural Design
supported by the sibling associations ACADIA, CAADRIA, eCAADe, SIGraDi, ASCAAD and CAAD futures

PDF papers
References

Hits 1 to 20 of 559

Reformat results as: short short into frame detailed detailed into frame

_id	caadria2014_042
id	caadria2014_042
authors	Alam, Jack and Jeremy J. Ham
year	2014
title	Towards a BIM-Based Energy Rating System
source	Rethinking Comprehensive Design: Speculative Counterculture, Proceedings of the 19th International Conference on Computer-Aided Architectural Design Research in Asia (CAADRIA 2014) / Kyoto 14-16 May 2014, pp. 285–294
doi	https://doi.org/10.52842/conf.caadria.2014.285
summary	Governments in Australia are faced with policy implementation that mandates higher energy efficient housing (Foran, Lenzen & Dey 2005). To this effect, the National Construction Code (NCC) 2013 stipulates the minimum energy performance for residential buildings as 114MJ/m2 per annum or 6 stars on an energy rating scale. Compliance with this minimum is mandatory but there are several methods through which residential buildings can be rated to comply with the deemed to satisfy provisions outlined in the NCC. FirstRate5 is by far the most commonly used simulation software used in Victoria, Australia. Meanwhile, Building Information Modelling (BIM), using software such as ArchiCAD has gained a foothold in the industry. The energy simulation software within ArchiCAD, EcoDesigner, enables the reporting on the energy performance based on BIM elements that contain thermal information. This research is founded on a comparative study between FirstRate5 and EcoDesigner. Three building types were analysed and compared. The comparison finds significant differences between simulations, being, measured areas, thermal loads and potentially serious shortcomings within FirstRate5, that are discussed along with the future potential of a fully BIM-integrated model for energy rating certification in Victoria.
keywords	Building Information Modelling, energy rating, FirstRate 5, ArchiCAD EcoDesigner, Building Energy Model
series	CAADRIA
email
last changed	2022/06/07 07:54

_id	ascaad2012_003
id	ascaad2012_003
authors	Elseragy, Ahmed
year	2012
title	Creative Design Between Representation and Simulation
source	CAAD \| INNOVATION \| PRACTICE [6th International Conference Proceedings of the Arab Society for Computer Aided Architectural Design (ASCAAD 2012 / ISBN 978-99958-2-063-3], Manama (Kingdom of Bahrain), 21-23 February 2012, pp. 11-12
summary	Milestone figures of architecture all have their different views on what comes first, form or function. They also vary in their definitions of creativity. Apparently, creativity is very strongly related to ideas and how they can be generated. It is also correlated with the process of thinking and developing. Creative products, whether architectural or otherwise, and whether tangible or intangible, are originated from ‘good ideas’ (Elnokaly, Elseragy and Alsaadani, 2008). On one hand, not any idea, or any good idea, can be considered creative but, on the other hand, any creative result can be traced back to a good idea that initiated it in the beginning (Goldschmit and Tatsa, 2005). Creativity in literature, music and other forms of art is immeasurable and unbounded by constraints of physical reality. Musicians, painters and sculptors do not create within tight restrictions. They create what becomes their own mind’s intellectual property, and viewers or listeners are free to interpret these creations from whichever angle they choose. However, this is not the case with architects, whose creations and creative products are always bound with different physical constraints that may be related to the building location, social and cultural values related to the context, environmental performance and energy efficiency, and many more (Elnokaly, Elseragy and Alsaadani, 2008). Remarkably, over the last three decades computers have dominated in almost all areas of design, taking over the burden of repetitive tasks so that the designers and students can focus on the act of creation. Computer aided design has been used for a long time as a tool of drafting, however in this last decade this tool of representation is being replaced by simulation in different areas such as simulation of form, function and environment. Thus, the crafting of objects is moving towards the generation of forms and integrated systems through designer-authored computational processes. The emergence and adoption of computational technologies has significantly changed design and design education beyond the replacement of drawing boards with computers or pens and paper with computer-aided design (CAD) computer-aided engineering (CAE) applications. This paper highlights the influence of the evolving transformation from Computer Aided Design (CAD) to Computational Design (CD) and how this presents a profound shift in creative design thinking and education. Computational-based design and simulation represent new tools that encourage designers and artists to continue progression of novel modes of design thinking and creativity for the 21st century designers. Today computational design calls for new ideas that will transcend conventional boundaries and support creative insights through design and into design. However, it is still believed that in architecture education one should not replace the design process and creative thinking at early stages by software tools that shape both process and final product which may become a limitation for creative designs to adapt to the decisions and metaphors chosen by the simulation tool. This paper explores the development of Computer Aided Design (CAD) to Computational Design (CD) Tools and their impact on contemporary design education and creative design.
series	ASCAAD
email
more	http://www.ascaad.org/conference/2012/papers/ascaad2012_003.pdf
last changed	2012/05/15 20:46

_id	acadia05_200
id	acadia05_200
authors	Tsou, J.-Y., Chan Yi Lee, Mak Kwok Pui, Ru Xu Du, Liang Jian, Yeung Kim
year	2005
title	Applying Scientific Simulation to Integrate Thermoelectric Conductor Module into Architectural Design – Smart Wall for Thermal Comfort
source	Smart Architecture: Integration of Digital and Building Technologies [Proceedings of the 2005 Annual Conference of the Association for Computer Aided Design In Architecture / ISBN 0-9772832-0-8] Savannah (Georgia) 13-16 October 2005, pp. 200-210
doi	https://doi.org/10.52842/conf.acadia.2005.200
summary	This paper presents the innovative architectural design concept, which is to integrate the new material and technology into the building design to achieve the thermal comfort and at the same time reduce the energy consumption of the building by making use of the renewable energy, including solar and wind energy. The system is developed based on the idea of regional thermal comfort in building. The advantage of the system is the environmental friendly approach, costless operation, reliability, flexibility, scalability and adaptability for the integration to the building design. With the design concept, we tried to do two application designs in two virtual sites. One is a badminton court for the 2008 Beijing Olympic Games and the other is a cooling pond in a shopping mall. We will introduce how computational simulation can contribute to the prediction of the performance of the design. We will also discuss how the computation simulation can help in the design optimization process. Through the development of the new design integration of the material to the building, we would like to feedback to the material industry to encourage further collaboration and development in the material enhancement, so that both industries and the society can benefit from the advancement.
series	ACADIA
email
last changed	2022/06/07 07:57

_id	acadia05_012
id	acadia05_012
authors	Anshuman, Sachin
year	2005
title	Responsiveness and Social Expression; Seeking Human Embodiment in Intelligent Façades
source	Smart Architecture: Integration of Digital and Building Technologies [Proceedings of the 2005 Annual Conference of the Association for Computer Aided Design In Architecture / ISBN 0-9772832-0-8] Savannah (Georgia) 13-16 October 2005, pp. 12-23
doi	https://doi.org/10.52842/conf.acadia.2005.012
summary	This paper is based on a comparative analysis of some twenty-six intelligent building facades and sixteen large media-facades from a socio-psychological perspective. It is not difficult to observe how deployment of computational technologies have engendered new possibilities for architectural production to which surface-centeredness lies at that heart of spatial production during design, fabrication and envelope automation processes. While surfaces play a critical role in contemporary social production (information display, communication and interaction), it is important to understand how the relationships between augmented building surfaces and its subjects unfold. We target double-skin automated facades as a distinct field within building-services and automation industry, and discuss how the developments within this area are over-occupied with seamless climate control and energy efficiency themes, resulting into socially inert mechanical membranes. Our thesis is that at the core of the development of automated façade lies the industrial automation attitude that renders the eventual product socially less engaging and machinic. We illustrate examples of interactive media-façades to demonstrate how architects and interaction designers have used similar technology to turn building surfaces into socially engaging architectural elements. We seek opportunities to extend performative aspects of otherwise function driven double-skin façades for public expression, informal social engagement and context embodiment. Towards the end of the paper, we propose a conceptual model as a possible method to address the emergent issues. Through this paper we intend to bring forth emergent concerns to designing building membrane where technology and performance are addressed through a broader cultural position, establishing a continual dialogue between the surface, function and its larger human context.
series	ACADIA
email
last changed	2022/06/07 07:54

_id	acadia05_170
id	acadia05_170
authors	Barker, Daniel and Dong, Andy
year	2005
title	A Representation Language for a Prototype CAD Tool for Intelligent Rooms
source	Smart Architecture: Integration of Digital and Building Technologies [Proceedings of the 2005 Annual Conference of the Association for Computer Aided Design In Architecture / ISBN 0-9772832-0-8] Savannah (Georgia) 13-16 October 2005, pp. 170-183
doi	https://doi.org/10.52842/conf.acadia.2005.170
summary	Intelligent rooms are a type of intelligent environment which enhance ordinary activities within the confines of a room by responding to human interaction using pervasive and ubiquitous computing. In the design of intelligent rooms, the specification of how the intelligent room enacts intelligent behavior through computational means is as integral as the geometric description. The self-aware and context-aware capabilities of intelligent rooms extend the requirements for computer-aided design tools beyond 3D modeling of objects. This article presents a Hardware as Agents Description Language for Intelligent Rooms (HADLIR) to model hardware in an intelligent room as “hardware agents” having sensor and/or effector modalities with rules and goals. End-users describe intelligent room hardware as agents based on the HADLIR representation and write agent rules and goals in Jess for each hardware component. This HADLIR agent description and the requisite software sensors/effectors constitute “hardware agents” which are instantiated into a multi-agent society software environment. The society is then bridged to either a virtual environment to prototype the intelligent room or to microelectronic controllers to implement a physical intelligent room. The integration illustrates how the HADLIR representation assists in the design, simulation and implementation of an intelligent room and provides a foundation technology for CAD tools for the creation of intelligent rooms.
series	ACADIA
email
last changed	2022/06/07 07:54

_id	2005_647
id	2005_647
authors	Caldas, Luisa G.
year	2005
title	Three-Dimensional Shape Generation of Low-Energy Architectural Solutions using Pareto Genetic Algorithms
source	Digital Design: The Quest for New Paradigms [23nd eCAADe Conference Proceedings / ISBN 0-9541183-3-2] Lisbon (Portugal) 21-24 September 2005, pp. 647-654
doi	https://doi.org/10.52842/conf.ecaade.2005.647
summary	This paper extends on a previous work on the application of a Generative Design System [GDS] to the evolution, in a computational environment, of three-dimensional architectural solutions that are energy-efficient and adapted to the climatic environment where they are located. The GDS combines a well-known building energy simulation software [DOE2.1E] with search procedures based on Genetic Algorithms and on Pareto optimization techniques, successfully allowing to tackle complex multi-objective problems. In the experiments described, architectural solutions based on a simplified layout were generated in response to two often-conflicting requirements: improving the use of daylighting in the space, while controlling the amount of energy loss through the building fabric. The choice of a cold climate like Chicago provided an adequate framework for studying the role of these opposing forces in architectural form generation. Analysis of results shows that building characteristics that originate successful solutions extend further than the building envelope. Issues of massing, aspect ratio, surface-to-volume ratio, orientation, and others, emerge from the analysis of solutions generated by the GDS, playing a significant role in dictating whether a given architectural form will prove adapted to its climatic and energy requirements. Results suggest that the questions raised by the exploration of form generation driven by environmental concerns are complex, deserving the pursuit of further experiments, in order to better understand the interaction of variables that the evolutionary process congregates.
keywords	Generative Design System, Genetic Algorithms, Evolutionary Architecture, Artificial Intelligence in Design, Building Energy Simulation, Bioclimatic Architecture, Environmental Design.
series	eCAADe
email
last changed	2022/06/07 07:54

_id	2005_407
id	2005_407
authors	Post, Jelle and Koutamanis, Alexander
year	2005
title	Simulation for Daylighting in the Real World
source	Digital Design: The Quest for New Paradigms [23nd eCAADe Conference Proceedings / ISBN 0-9541183-3-2] Lisbon (Portugal) 21-24 September 2005, pp. 407-414
doi	https://doi.org/10.52842/conf.ecaade.2005.407
summary	Technology has been an obvious solution to the increasing complexity of the built environment. As the number and specificity of use requirements increases, designers, clients and managers tend to segment the overall problem to manageable aspects only tentatively linked to each other. As a result, aspects such as ventilation and lighting tend to rely more on mechanical means than on the affordances of the overall design. Ironically this increases the complexity and opacity of the built environment probably to a greater extent than rules, regulations and requirements. The paper presents a review of available computational methods and techniques that aim at a more coherent approach by supporting integration of (day)lighting into architectural designing. It proposes that the two main courses of further action are the improvement and updating building regulations, and the combination of quantitative knowledge of good, existing daylight designs with advanced simulation-based analyses of early design proposals. Improvements in daylighting design and the integration of daylighting in design solutions depend primarily on design guidance based on the coordinated development and thorough understanding of usable measures such as the Daylight Factor, the Daylight Performance Index and function factors. A major prerequisite to both simulation and design guidance are robust and detailed geometrical 3D models that accommodate both the input and the output of design actions and transactions.
keywords	Simulation; Daylight; Integration
series	eCAADe
email
last changed	2022/06/07 08:00

_id	acadia05_128
id	acadia05_128
authors	Sanchez-Del-Valle, Carmina
year	2005
title	Adaptive Kinetic Architecture: A Portal To Digital Prototyping
source	Smart Architecture: Integration of Digital and Building Technologies [Proceedings of the 2005 Annual Conference of the Association for Computer Aided Design In Architecture / ISBN 0-9772832-0-8] Savannah (Georgia) 13-16 October 2005, pp. 128-140
doi	https://doi.org/10.52842/conf.acadia.2005.128
summary	This paper presents a definition for adaptive kinetic structures in architecture, generated from an examination of research in engineering and architecture. This characterization introduces the challenges presented both by modeling form and environment, and simulating their interaction. Adaptive kinetic structures react to a changing environment, as well as generate their own. These conditions make them appropriate subjects through which the design and implementation of tools for ‘digital prototyping’ may be explored. Digital prototyping serves performance and simulation-based design. In general terms, it is an interdisciplinary integrated approach for modeling, predicting, and analyzing the behavior of a system. It is at the core of virtual engineering. In the aerospace, automobile, and manufacturing industries, it is practiced extensively through discrete-event and continuous simulations, as well as simulation environments. This paper provides an overview of digital prototyping commercial software for engineering applications that can be transferred to architecture, and identifies some of the unresolved issues. It thereby extends the vision of the comprehensive building information modeling initiative.
series	ACADIA
email
last changed	2022/06/07 07:56

_id	sigradi2005_483
id	sigradi2005_483
authors	Abdelhameed, Wael
year	2005
title	Digital-Media Impact on the Representation Capability of Architects
source	SIGraDi 2005 - [Proceedings of the 9th Iberoamerican Congress of Digital Graphics] Lima - Peru 21-24 november 2005, vol. 1, pp. 483-489
summary	Architects draw to define design problems, to construct concepts, or to explore ideas. Representation not only connects various design activities and tasks, but also is utilized inside all these activities and tasks. Within the context of this research, the Design Capabilities of architects are defined as the skills used during the design process, including Conceptualization, Representation, Form Giving, Knowledge Building and Retrieving, and Decision-Making. Using representational techniques introduced by digital media during design development has altered what we can represent, perceive, and therefore conceive and imagine. Depending on primary data (a global questionnaire) and secondary data (synthesis of previous researches), the results of this investigation have substantiated that there has been a positive impact of digital media settings on the output of Representation capability of architects. The analysis reveals some detailed findings, which provide a better understanding of the subject matter.
series	SIGRADI
email
last changed	2016/03/10 09:47

_id	ascaad2014_023
id	ascaad2014_023
authors	Al-Maiyah, Sura and Hisham Elkadi
year	2014
title	Assessing the Use of Advanced Daylight Simulation Modelling Tools in Enhancing the Student Learning Experience
source	Digital Crafting [7th International Conference Proceedings of the Arab Society for Computer Aided Architectural Design (ASCAAD 2014 / ISBN 978-603-90142-5-6], Jeddah (Kingdom of Saudi Arabia), 31 March - 3 April 2014, pp. 303-313
summary	In architecture schools, where the ‘studio culture’ lies at the heart of students’ learning, taught courses, particularly technology ones, are often seen as secondary or supplementary units. Successful delivery of such courses, where students can act effectively, be motivated and engaged, is a rather demanding task requiring careful planning and the use of various teaching styles. A recent challenge that faces architecture education today, and subsequently influences the way technology courses are being designed, is the growing trend in practice towards environmentally responsive design and the need for graduates with new skills in sustainable construction and urban ecology (HEFCE’s consultation document, 2005). This article presents the role of innovative simulation modelling tools in the enhancement of the student learning experience and professional development. Reference is made to a teaching practice that has recently been applied at Portsmouth School of Architecture in the United Kingdom and piloted at Deakin University in Australia. The work focuses on the structure and delivery of one of the two main technology units in the second year architecture programme that underwent two main phases of revision during the academic years 2009/10 and 2010/11. The article examines the inclusion of advanced daylight simulation modelling tools in the unit programme, and measures the effectiveness of enhancing its delivery as a key component of the curriculum on the student learning experience. A main objective of the work was to explain whether or not the introduction of a simulation modelling component, and the later improvement of its integration with the course programme and assessment, has contributed to a better learning experience and level of engagement. Student feedback and the grade distribution pattern over the last three academic years were collected and analyzed. The analysis of student feedback on the revised modelling component showed a positive influence on the learning experience and level of satisfaction and engagement. An improvement in student performance was also recorded over the last two academic years and following the implementation of new assessment design.
series	ASCAAD
email
last changed	2016/02/15 13:09

_id	2005_763
id	2005_763
authors	Beilharz, Kirsty
year	2005
title	Architecture as the Computer Interface: 4D Gestural Interaction with Socio-Spatial Sonification
source	Digital Design: The Quest for New Paradigms [23nd eCAADe Conference Proceedings / ISBN 0-9541183-3-2] Lisbon (Portugal) 21-24 September 2005, pp. 763-770
doi	https://doi.org/10.52842/conf.ecaade.2005.763
summary	Architecture today extends far beyond designing building shells and material, peripheral boundaries. Arguably, it has always been, and shifts increasingly in contemporary environments towards, designing space and interaction with space. Hence, the role of the designer includes integration of computing in architecture through ambient display and non-tactile interaction. This paper explores a framework in which the architecture is the computer interface to information sonification. (Sonification is automatically generated representation of information using sound). The examples in this paper are Emergent Energies, demonstrating a socio-spatially responsive generative design in a sensate environment enabled by pressure mats; Sensor-Cow using wireless gesture controllers to sonify motion; and Sonic Kung Fu which is an interactive sound sculpture facilitated by video colour-tracking. The method in this paper connects current information sonification methodologies with gesture controller capabilities to complete a cycle in which gestural, non-tactile control permutes and interacts with automatically-generated information sonification. Gestural pervasive computing negotiates space and computer interaction without conventional interfaces (keyboard/mouse) thus freeing the user to monitor or display information with full mobility, without fixed or expensive devices. Integral computing, a blurring of human-machine boundaries and embedding communication infrastructure, ambient display and interaction in the fabric of architecture are the objectives of this re-thinking.
keywords	Interactive Sonification, Gesture Controllers, Responsive Spaces, SpatialSound
series	eCAADe
email
last changed	2022/06/07 07:54

_id	ascaad2006_paper29
id	ascaad2006_paper29
authors	Bennadji, A. and A. Bellakha
year	2006
title	Evaluation of a Higher Education Self-learning Interface
source	Computing in Architecture / Re-Thinking the Discourse: The Second International Conference of the Arab Society for Computer Aided Architectural Design (ASCAAD 2006), 25-27 April 2006, Sharjah, United Arab Emirates
summary	This paper is a follow-up to a previous paper published in ASCAAD 2004 (A. Bennadji et al 2005). The latter reported on CASD (Computer Aided Sustainable Design) a self-learning educational interface which assists the various building’s actors in their design with a particular attention to the aspect of energy saving. This paper focuses on the importance of software evaluation and how the testing is done to achieve a better human-machine interaction. The paper will go through the summative evaluation of CASD, presents the output of this evaluation and addresses the challenge facing software developers: how to make an interface accessible to all users and specifically students in higher education.
series	ASCAAD
email
last changed	2007/04/08 19:47

_id	cf2005_1_83_123
id	cf2005_1_83_123
authors	BRUNNER Klaus A. and MAHDAVI Ardeshir
year	2005
title	A Software Architecture for Self-updating Life-cycle Building Models
source	Computer Aided Architectural Design Futures 2005 [Proceedings of the 11th International Conference on Computer Aided Architectural Design Futures / ISBN 1-4020-3460-1] Vienna (Austria) 20–22 June 2005, pp. 423-432
summary	This paper describes a computational infrastructure for the realization of a self-updating building information model conceived in the design phase and carried over to the operation phase of a building. As such, it illustrates how computational representations of buildings, which typically serve design support, documentation, and communication functions, can be transported into the post-construction phase. Toward this end, we formulate a number of requirements for the conception and maintenance of life-cycle building information models. Moreover, we describe the architecture and the prototypical implementation of such a model.
keywords	building models, sensors, simulation-based control, life-cycle
series	CAAD Futures
email
last changed	2006/11/07 07:27

_id	sigradi2005_603
id	sigradi2005_603
authors	Castañé, Dora; Claudio Deho, Adrián Barcesat, Carlos Tessier
year	2005
title	Urbamedia: the design of an integrated system of urban-building visualization and communication
source	SIGraDi 2005 - [Proceedings of the 9th Iberoamerican Congress of Digital Graphics] Lima - Peru 21-24 november 2005, vol. 2, pp. 603-608
summary	This paper presents the advancements of the Urbamedia project which was designed as part of a research program at the Center CAO (Creation computer assist), School of Architectural Design and Urbanism, University of Buenos Aires, which was led by the valued master and advisory professor Architect Arturo F. Montagu. This proposal of the city of Buenos Aires on the Mayo Avenue expands the original historical fragment presented between the following two referenced representative landmarks: The Two Congresses Square and the Mayo Square. It continues with the advancement of methodologies and techniques implemented in a system of “integrated visualization and communication” for the development of a VRML (Virtual Reality Modeling Language) 3D virtual non-immersive and interactive vision. It also incorporates the development of a “foundation of digitally integrated knowledge” with fragments of central areas from other surrounding cities as well as interfaced phenomenological situations. The application of digital VRML technology has allowed for thoroughly researching the processes through dynamic simulation of specific urban fragments (Mayo Avenue within Buenos Aires) and the cities that are also participating in the project. [Full paper in Spanish]
series	SIGRADI
email
last changed	2016/03/10 09:48

_id	2005_501
id	2005_501
authors	Celani, Gabriela, Pupo, Regiane, Mendes, Gelly and Pinheiro, Érica
year	2005
title	Generative Design Systems for Housing
source	Digital Design: The Quest for New Paradigms [23nd eCAADe Conference Proceedings / ISBN 0-9541183-3-2] Lisbon (Portugal) 21-24 September 2005, pp. 501-506
doi	https://doi.org/10.52842/conf.ecaade.2005.501
summary	The present paper describes an undergoing research that aims at developing a generative design computer implementation with an outside-in approach, OIDS. The system will allow developing and visualizing context-based housing development designs. This approach will include both natural characteristics of the site and the existing neighboring buildings. It is argued that certain common urban design practices are the result of a simplification due to difficulties in dealing with the irregularities of the natural environment, which often requires the use of time-consuming methods. The computer-based application will provide tools for dealing with such difficulties, allowing designers to describe their own design rules. In an initial phase of the project, a tool that can subdivide irregular land parcels into equally sized areas has been developed. In further stages, other environmental variables will be addressed, such as solar aspect and prevalent wind directions. Eventually, even the designs of interior layouts should result from exterior forces. The resulting generative system is expected to facilitate and encourage the use of a more organic approach to building siting and design, bringing about the important discussion about which should be the main forces in the generation of the built environment.
keywords	Generative Design; Context-Based Design; Housing Design; Building Siting; Urban Space Simulation
series	eCAADe
email
last changed	2022/06/07 07:55

_id	cf2011_p051
id	cf2011_p051
authors	Cote, Pierre; Mohamed-Ahmed Ashraf, Tremblay Sebastien
year	2011
title	A Quantitative Method to Compare the Impact of Design Mediums on the Architectural Ideation Process.
source	Computer Aided Architectural Design Futures 2011 [Proceedings of the 14th International Conference on Computer Aided Architectural Design Futures / ISBN 9782874561429] Liege (Belgium) 4-8 July 2011, pp. 539-556.
summary	If we compare the architectural design process to a black box system, we can assume that we now know quite well both inputs and outputs of the system. Indeed, everything about the early project either feasibility studies, programming, context integration, site analysis (urban, rural or natural), as well as the integration of participants in a collaborative process can all be considered to initiate and sustain the architectural design and ideation process. Similarly, outputs from that process are also, and to some extent, well known and identifiable. We are referring here, among others, to the project representations or even to the concrete building construction and its post-evaluation. But what about the black box itself that produces the ideation. This is the question that attempts to answer the research. Currently, very few research works linger to identify how the human brain accomplishes those tasks; how to identify the cognitive functions that are playing this role; to what extent they operate and complement each other, and among other things, whether there possibly a chain of causality between these functions. Therefore, this study proposes to define a model that reflects the activity of the black box based on the cognitive activity of the human brain. From an extensive literature review, two cognitive functions have been identified and are investigated to account for some of the complex cognitive activity that occurs during a design process, namely the mental workload and mental imagery. These two variables are measured quantitatively in the context of real design task. Essentially, the mental load is measured using a Bakan's test and the mental imagery with eyes tracking. The statistical software G-Power was used to identify the necessary subject number to obtain for significant variance and correlation result analysis. Thus, in the context of an exploratory research, to ensure effective sample of 0.25 and a statistical power of 0.80, 32 participants are needed. All these participants are students from 3rd, 4th or 5th grade in architecture. They are also very familiar with the architectural design process and the design mediums used, i.e., analog model, freehand drawing and CAD software, SketchUp. In three experimental sessions, participants were asked to design three different projects, namely, a bus shelter, a recycling station and a public toilet. These projects were selected and defined for their complexity similarity, taking into account the available time of 22 minutes, using all three mediums of design, and this in a randomly manner to avoid the order effect. To analyze the two cognitive functions (mental load and mental imagery), two instruments are used. Mental imagery is measured using eye movement tracking with monitoring and quantitative analysis of scan paths and the resulting number and duration of participant eye fixations (Johansson et al, 2005). The mental workload is measured using the performance of a modality hearing secondary task inspired by Bakan'sworks (Bakan et al.; 1963). Each of these three experimental sessions, lasting 90 minutes, was composed of two phases: 1. After calibrating the glasses for eye movement, the subject had to exercise freely for 3 minutes while wearing the glasses and headphones (Bakan task) to get use to the wearing hardware. Then, after reading the guidelines and criteria for the design project (¬± 5 minutes), he had 22 minutes to execute the design task on a drawing table allowing an upright posture. Once the task is completed, the subject had to take the NASA TLX Test, on the assessment of mental load (¬± 5 minutes) and a written post-experimental questionnaire on his impressions of the experiment (¬± 10 minutes). 2. After a break of 5-10 minutes, the participant answered a psychometric test, which is different for each session. These tests (¬± 20 minutes) are administered in the same order to each participant. Thus, in the first experimental session, the subject had to take the psychometric test from Ekstrom et al. (1978), on spatial performance (Factor-Referenced Cognitive Tests Kit). During the second session, the cognitive style is evaluated using Oltman's test (1971). Finally, in the third and final session, participant creativity is evaluated using Delis-Kaplan test (D-KEFS), Delis et al. (2001). Thus, this study will present the first results of quantitative measures to establish and validate the proposed model. Furthermore, the paper will also discuss the relevance of the proposed approach, considering that currently teaching of ideation in ours schools of architecture in North America is essentially done in a holistic manner through the architectural project.
keywords	design, ideation process, mental workload, mental imagery, quantitative mesure
series	CAAD Futures
email
last changed	2012/02/11 19:21

_id	cf2005_1_82_21
id	cf2005_1_82_21
authors	DE VRIES Bauke and HARINK Jeroen
year	2005
title	Construction Analysis during the Design Process
source	Computer Aided Architectural Design Futures 2005 [Proceedings of the 11th International Conference on Computer Aided Architectural Design Futures / ISBN 1-4020-3460-1] Vienna (Austria) 20–22 June 2005, pp. 413-422
summary	4D CAD systems are used by contractors for visually checking the construction process. To enable simulation of the construction process, the construction planner links building components from a CAD model with the activities from a project planning. In this paper we describe a method to generate a project planning directly from a CAD model using basic construction knowledge. A case study is discussed briefly to show the current results and the shortcomings. Finally an outlook is presented on a more advanced implementation that is (also) useful for designers.
keywords	4D CAD, design process, construction analysis, automatic planning
series	CAAD Futures
email
last changed	2006/11/07 07:27

_id	6b43
id	6b43
authors	Heylighen A, Casaer M, Neuckermans H
year	2005
title	SHARING-IN-ACTION. HOW DESIGNERS CAN SHARE INSIGHTS WITHOUT KNOWING
source	P. Kommers & P. Isaías (eds), Web Based Communities 2005, Proceedings of the IADIS International Conference on Web-Based Communities 2005, Algarve (Portugal), Feb 2005, pp.238-245 (ISBN 972-99353-7-8)
summary	In architecture, design ideas are developed as much through interaction as by individuals in isolation. This awareness inspired the development of a Dynamic Architectural Memory On-line, an interactive platform to share ideas, knowledge and insights in the form of concrete building projects among designers in different contexts and at different levels of expertise. Interaction with various user groups revealed this platform to suffer from at least two thresholds. First of all, making projects available to other platform users takes time, effort, and specific skills. Secondly, designers tend to sense a psychological threshold to share their ideas and insights with others. In trying to tackle both thresholds, this paper proposes to conceive the platform as an associative network of projects, and develops ideas about how the relationships in this network can be determined and updated by exploiting the insights implicitly available in the project documentation and user (inter)actions. In the long run, this should allow the platform to learn from all designers using the platform, including those who do not release information on their own projects, and to apply the lessons learned to continuously enhance its performance.
keywords	web-based communities, self-organization, data mining, design experience
series	other
type	normal paper
email
last changed	2005/04/01 13:25

_id	caadria2017_062
id	caadria2017_062
authors	Ji, Seung Yeul, Kim, Mi Kyoung and Jun, Han Jong
year	2017
title	Campus Space Management Using a Mobile BIM-based Augmented Reality System
source	P. Janssen, P. Loh, A. Raonic, M. A. Schnabel (eds.), Protocols, Flows, and Glitches - Proceedings of the 22nd CAADRIA Conference, Xi'an Jiaotong-Liverpool University, Suzhou, China, 5-8 April 2017, pp. 105-114
doi	https://doi.org/10.52842/conf.caadria.2017.105
summary	In South Korea, the changing paradigm of family composition toward single-person households and nuclear families has caused the decrease in number of students, which has led to the need for change in the qualitative, rather than quantitative, management of spaces and facilities on university campuses. In particular, since 2005, the merging of universities have accelerated, which has brought up the need for a system that facilitates the management of integrated university systems. Accordingly, universities now require efficient system operation based on three-dimensional and data visualization, unlike the document-based management of facilities and spaces in the past. Users lack a sense of responsibility for public facilities, causing difficulties such as energy waste and frequent movement, as well as damage and theft of goods. This study aims to form an AR-based interface using the ANPR algorithm, a computer vision technique, and the position-based data of the GPS. It also aims to build a campus space management system to overcome the limitations of current systems and to effectively and systematically manage integrated building data. In addition, for module test verification, the prototype is applied to actual campus spaces, and additional demands for campus space management in the AR application are identified and organized.
keywords	augmented reality; Campus space management; BIM; CAFM (computer-aided facilities management); user experience (UX)
series	CAADRIA
email
last changed	2022/06/07 07:52

_id	acadia05_048
id	acadia05_048
authors	Katodrytis, George
year	2005
title	Poiesis and Autopoiesis in Architecture
source	Smart Architecture: Integration of Digital and Building Technologies [Proceedings of the 2005 Annual Conference of the Association for Computer Aided Design In Architecture / ISBN 0-9772832-0-8] Savannah (Georgia) 13-16 October 2005, pp. 48-57
doi	https://doi.org/10.52842/conf.acadia.2005.048
summary	The use of digital technology in architecture has proven to be more assertive than originally thought: it has reconditioned the nature of the design process, and established new processes and techniques of fabrication. Recent applications in digital technology show inquisitiveness in the contentious subject Genetic Algorithms. This new architectural process is characterized by two main shifts: from poiesis (or poetry) to autopoiesis, and from authenticity to mimesis. Since evolutionary simulations give rise to new forms rather than design them, architects should now be both artists and operators of both Inventive and Systematic design. Inventive design: The digital media should bring about poiesis (poetry). Digital spaces reveal and visualize the unconscious desires of urban spaces, bringing forth new dreamscapes, mysterious and surreal. This implies a Freudian spatial unconscious, which can be subjected to analysis and interpretation. The tools of digital dreaming, meanwhile, have opened a window to the ‘urban unconscious’. Systematic Design: Digital media should bring about an autopoiesis. This approach calls into question traditional methods of architectural design that replace the hierarchical processes of production known as “cause and effect,” and propose a design process where the architect becomes a constructor of formal systems. Will the evolutionary simulation replace design? Is metric space dead? The new algorithmic evolutionary conditions give architecture an autopoiesis, similar to biological dynamics. Paradoxically, the new emerging process is more insightful. The emphasis of the exploration is on morphological complexity. Architecture, through “machine” fabrication, may become more responsive, rigorous and poetic.
series	ACADIA
email
last changed	2022/06/07 07:52

For more results click below: