Cumincad : CUMINCAD Papers : Search Results

CumInCAD is a Cumulative Index about publications in Computer Aided Architectural Design
supported by the sibling associations ACADIA, CAADRIA, eCAADe, SIGraDi, ASCAAD and CAAD futures

PDF papers
References

Hits 1 to 20 of 621

Reformat results as: short short into frame detailed detailed into frame

_id	bsct_dervishi
id	bsct_dervishi
authors	Dervishi, Sokol
year	2006
title	Computational Derivation of Incident Irradiance on Building Facades based on Measured Global Horizontal Irradiance Data
source	Vienna University of Technology; Building Science & Technology
summary	Reliable simulation of buildings' energy performance requires, amongst other things, the availability of detailed information on the magnitudes of incident solar radiation on building facades. However, the availability of the measured data concerning the incident solar radiation on vertical surfaces is restricted to only few locations. In addition, concurrent measurements of horizontal global and horizontal diffuse (or direct normal) irradiance data are likewise available only for a limited number of locations. In contrast, global horizontal irradiance data is available for many locations. This research demonstrates how to computationally derive incident irradiance values on vertical (or otherwise inclined) building surfaces from measured globalirradiance values. Given this context, three methods are considered to compute incident vertical irradiance values based on measured global horizontal irradiance data. Vertical solar irradiance measurements are described. Then, the computationally derived values are compared withcorresponding measurements. The results are evaluated based on their correlation coefficients and relative error. Finally, the application of horizontal-to- vertical irradiance mapping is demonstrated using the case of an office building at Vienna University of Technology.
keywords	Horizontal and vertical irradiance, measurement and simulation, energy performance
series	thesis:MSc
type	normal paper
email
more	http://cec.tuwien.ac.at
last changed	2006/07/02 22:30

_id	ddss2006-pb-415
id	DDSS2006-PB-415
authors	Ching-Shun Tang
year	2006
title	Smart Structure: Designs with Rapid Prototyping
source	Van Leeuwen, J.P. and H.J.P. Timmermans (eds.) 2006, Progress in Design & Decision Support Systems in Architecture and Urban Planning, Eindhoven: Eindhoven University of Technology, ISBN-10: 90-386-1756-9, ISBN-13: 978-90-386-1756-5, p. 415-429
summary	This research presents the new orientation of the combination of digital modelling with generative programming and joint method of traditional wood structure for manipulating Rapid Prototyping to explore the assembling of free form objects. The presenting of the example indicates that the edition of Maya scripts defines the purpose of design. Through the discussion on scripts developing the assembly of the free-form objects of frames and surfaces and through the achievement that RP produces and examines objects, we bring out the possibilities of the new form developed from the old structure and illustrate how to develop our hypothesis. The developed result could provide the possible new way for free-form assembly. We expatiate our research process and final achievement and provide a new thinking direction in the education field.
keywords	CAD/CAM, Digital fabrication, Rapid prototyping, Traditional wood structure
series	DDSS
last changed	2006/08/29 12:55

_id	ddss2006-hb-433
id	DDSS2006-HB-433
authors	Eric Landreneau, Ozan O. Ozener, Burak Pak, Ergun Akleman, and John Keyser
year	2006
title	Interactive Rule-Based Design - An experimental interface for conceptual design
source	Van Leeuwen, J.P. and H.J.P. Timmermans (eds.) 2006, Innovations in Design & Decision Support Systems in Architecture and Urban Planning, Dordrecht: Springer, ISBN-10: 1-4020-5059-3, ISBN-13: 978-1-4020-5059-6, p. 433-446
summary	In this paper, we present a method that allows designers to interactively create partially self-similar manifold surfaces without relying on shape grammars or fractal methods. The modellers that are based on traditional fractal methods or shape grammars usually create disconnected surfaces and restrict the creative freedom of users. In most cases, the shapes through conventional fractal or shape grammar methods are defined by hard coded schemes that allow limited interactivity for the design process. We present a new approach for modelling such shapes. With this approach, we have developed a simple generative tool with given adjustable parameters to achieve variety of conceptual forms. Using this tool, designers can interactively create a variety of partially self-similar manifold surfaces.
keywords	Fractal geometry, Conceptual design, Generative systems
series	DDSS
last changed	2006/08/29 12:55

_id	a126
id	a126
authors	Finucane E, Derix C and Coates P
year	2006
title	Evolving Urban Structures using Computational Optimisation
source	Proceedings of the Generative Arts conference, Milan, 2006
summary	This paper investigates the use of computer analogies for naturally inspired optimisation techniques as an aid to developing the site layout and massing for the new World Trade Centre development in Pristina Kosovo, which is being designed and developed by 4M Group architectural company, in conjunction with the Advanced Modelling Group Aedas. The development of a genetic algorithm will incorporate various techniques, that have been developed in the field of multi-objective optimisation, to create three dimensional massing models, and site layout solutions which partially fulfil the Prisina brief requirements, which are taken from specifications created by 4M Group. Genetic algorithms are based on natural evolutionary principles which are explained in this paper. It will incorporate Pareto concepts to manage the optimisation of the various objective functions. For example, these will include volume and position of units, which will ensure that the different and sometime conflicting needs of the site are balanced throughout the optimisation. This type of problem is often known as an NP-complete (non-determinate polynomial time) problem. This will provide architects and planners with a number of Pareto optimised site massing solutions as an aid to the design process. An initial investigation into the specifics of the Pristina site requirements, will be followed by an investigation into the the genetic algorithm which is created in Visual Basic for Applications (VBA) linked with AutoCAD as the graphical output of the code. The embryology (development) of the various solutions from the genetic information incorporates an ‘ant’ pheromone trail model, which simulates the action of ants during food foraging, as a tool for initial route planning within the site. Diffusion and cellular automata are used during the development of the solution to construct the massing for the site.
keywords	urban planning, evolutionary algorithms, pareto optimization, Lindenmayer systems, ant-colony optimization, cellular automaton
series	other
type	normal paper
email
more	http://www.generativeart.com/
last changed	2012/09/20 18:33

_id	sigradi2006_e185d
id	sigradi2006_e185d
authors	Geva, Anat and Mukherji, Anuradha
year	2006
title	The Holy Darkness: A Study of Light in Brihadeshvara Hindu Temple, in Tanjore, Tamilnadu, India (1010 AD)
source	SIGraDi 2006 - [Proceedings of the 10th Iberoamerican Congress of Digital Graphics] Santiago de Chile - Chile 21-23 November 2006, pp. 425-428
summary	The study investigates how religious principles govern the treatment of light/darkness in sacred monument. Specifically, a digitized daylight simulation is used in the analysis of Brihadeshvara Hindu Temple, built in 1010 AD in Tanjore, Tamilnadu, India. This sacred monument, listed as one of UNESCO's World Heritage Sites, is an intriguing case study since the treatment of the 'holy light' in the temple is the treatment of the 'holy darkness'.In spite of the importance given to sun in ancient Hindu scriptures, natural light was used very sparsely in Hindu temples. According to Hindu religious belief, when a worshipper is in the presence of the divine, there should be nothing to distract his/her senses (including vision). Therefore, the innermost sanctum is shrouded in total darkness and the progression into the temple is a ritual movement where the devotee goes through the dynamic experience of the darkening spaces of the temple before reaching the dark sacred chamber (see Fig.1). The dictation of the Hindu faith to create this spiritual procession toward the 'holy darkness' is examined in the historic Brihadeshvara Temple by using Lightscape -- computerized lighting simulation software. To run the program, a 3-D CAD surface model of the temple was created and imported into Lightscape. Then the model was assigned materials and its openings and lighting systems were defined. The simulations were run on four interior horizontal (floor) and vertical (walls) surfaces, along four spaces of the procession in the temple. The simulation targeted three time frames: sunrise, sunset and at high noon on March 21st (the equinox). The location of Tanjore, India was used for light conditions. The Lightscape simulations used the process of radiosity to generate single frame daylight renderings along with light analysis of each surface. A lighting animation was then produced in Quick Time.The results of this analysis demonstrate that the average illumination values for specific surfaces of the temple along the procession sequence correspond to the schematic expectation depicted in Figure 1, i.e., a progressively decreased luminance towards the dark innermost chamber. Furthermore, the simulated values were compared to the Illuminating Engineering Society (IES) standards, which recommend ranges of luminance for specific visual tasks and areas. The comparisons showed that the average luminance in the temple, from the illuminated entrance in the east to the darker chamber in the west, is lower than the IES standards for 'public places with dark surroundings' for 'short temporary visits'. Finally, a morphological analysis of the temple along accepted daylight design guidelines corroborated the previous findings. The multi-method investigation of the relationship of light and darkness, light and objects, and the designated light quality in the Brihadeshvara Temple demonstrates the strong influence of the specific dictum of Hinduism on the light/darkness treatment in the temple. The paper concludes that digitized media such as computerized daylight simulations can examine the significance of light/darkness in sacred monuments as a spiritual experience. This quantitative investigation can augment the qualitative studies in the field of historic sacred architecture.
series	SIGRADI
email
last changed	2016/03/10 09:52

_id	sigradi2006_e171c
id	sigradi2006_e171c
authors	González Böhme, Luis Felipe and Vargas Cárdenas, Bernardo
year	2006
title	Foundations for a Constraint-Based Floor Plan Layout Support in Participatory Planning of Low-Income Housing
source	SIGraDi 2006 - [Proceedings of the 10th Iberoamerican Congress of Digital Graphics] Santiago de Chile - Chile 21-23 November 2006, pp. 283-287
summary	We introduce the foundations of a novel approach that deals with constraint-based design methods to supporting participatory planning processes of low-income dwellings. We examine the space allocation problem inside the architectural domain on the basis of graph theory and combinatorics, providing a concise mathematical background for an implementation strategy called FLS (Floor plan Layout Support), which is analyzed here for the first time regarding this particular context of application. The philosophy underlying a design method that is mainly driven by the formulation of distinct constraints suggests to avoid the traditional procedure of first to create a yet not necessarily valid instance of the eventual design solution by directly choosing specific parameter values of its shape, and later on to evaluate its validity by confronting the designed model to a set of applicable constraints. Instead, constraint-based design poses a search procedure that operates in a space of planning-relevant constraint sets. The FLS methodology integrates some few principles of constraint-based automated reasoning with high user interactivity, into a design environment where as much dwellers as planners can collaboratively work in solving spatial organization problems of housing projects. The FLS model of application makes use of a combination of dweller-specified constraints, planning and zoning regulations, and a small library of modular space units. Constraint-based design ! methods are particularly capable of supplying efficient support for the collaborative involvement of dwellers into the architectural programming process of her/his own home. Mainly, because dwellers themselves tend to describe their space need and design intentions as a set of constraints on room quantity, space utilization, circulation system, allocation of available furniture, available budget, construction time, and so forth. The goal is to achieve an integrated tool for finding and modelling topologically valid solutions for floor plan layout alternatives, by combining user-driven interactive procedures with automatic search and generative processes. Thus, several design alternatives can be explored in less time and with less effort than using mainstream procedures of architectural practice. A FLS implementation will constitute one system module of a larger integrated system model called Esther. A FLS tool shall interact with other functional modules, like e.g. the BDS (Building Bulk Design Support), which also uses constraint-based design methods. A preliminary procedural model for the FLS was tested on Chile’s official social housing standards (Chilean Building Code – OGUC. Art. 6.4.1) which are very similar to most Latin American housing programs currently in operation.
keywords	constraint-based design; floor plan layout; participatory planning; low-income housing; design theory; design proces
series	SIGRADI
email
last changed	2016/03/10 09:52

_id	sigradi2006_e028c
id	sigradi2006_e028c
authors	Griffith, Kenfield; Sass, Larry and Michaud, Dennis
year	2006
title	A strategy for complex-curved building design:Design structure with Bi-lateral contouring as integrally connected ribs
source	SIGraDi 2006 - [Proceedings of the 10th Iberoamerican Congress of Digital Graphics] Santiago de Chile - Chile 21-23 November 2006, pp. 465-469
summary	Shapes in designs created by architects such as Gehry Partners (Shelden, 2002), Foster and Partners, and Kohn Peterson and Fox rely on computational processes for rationalizing complex geometry for building construction. Rationalization is the reduction of a complete geometric shape into discrete components. Unfortunately, for many architects the rationalization is limited reducing solid models to surfaces or data on spread sheets for contractors to follow. Rationalized models produced by the firms listed above do not offer strategies for construction or digital fabrication. For the physical production of CAD description an alternative to the rationalized description is needed. This paper examines the coupling of digital rationalization and digital fabrication with physical mockups (Rich, 1989). Our aim is to explore complex relationships found in early and mid stage design phases when digital fabrication is used to produce design outcomes. Results of our investigation will aid architects and engineers in addressing the complications found in the translation of design models embedded with precision to constructible geometries. We present an algorithmically based approach to design rationalization that supports physical production as well as surface production of desktop models. Our approach is an alternative to conventional rapid prototyping that builds objects by assembly of laterally sliced contours from a solid model. We explored an improved product description for rapid manufacture as bilateral contouring for structure and panelling for strength (Kolarevic, 2003). Infrastructure typically found within aerospace, automotive, and shipbuilding industries, bilateral contouring is an organized matrix of horizontal and vertical interlocking ribs evenly distributed along a surface. These structures are monocoque and semi-monocoque assemblies composed of structural ribs and skinning attached by rivets and adhesives. Alternative, bi-lateral contouring discussed is an interlocking matrix of plywood strips having integral joinery for assembly. Unlike traditional methods of building representations through malleable materials for creating tangible objects (Friedman, 2002), this approach constructs with the implication for building life-size solutions. Three algorithms are presented as examples of rationalized design production with physical results. The first algorithm [Figure 1] deconstructs an initial 2D curved form into ribbed slices to be assembled through integral connections constructed as part of the rib solution. The second algorithm [Figure 2] deconstructs curved forms of greater complexity. The algorithm walks along the surface extracting surface information along horizontal and vertical axes saving surface information resulting in a ribbed structure of slight double curvature. The final algorithm [Figure 3] is expressed as plug-in software for Rhino that deconstructs a design to components for assembly as rib structures. The plug-in also translates geometries to a flatten position for 2D fabrication. The software demonstrates the full scope of the research exploration. Studies published by Dodgson argued that innovation technology (IvT) (Dodgson, Gann, Salter, 2004) helped in solving projects like the Guggenheim in Bilbao, the leaning Tower of Pisa in Italy, and the Millennium Bridge in London. Similarly, the method discussed in this paper will aid in solving physical production problems with complex building forms. References Bentley, P.J. (Ed.). Evolutionary Design by Computers. Morgan Kaufman Publishers Inc. San Francisco, CA, 1-73 Celani, G, (2004) “From simple to complex: using AutoCAD to build generative design systems” in: L. Caldas and J. Duarte (org.) Implementations issues in generative design systems. First Intl. Conference on Design Computing and Cognition, July 2004 Dodgson M, Gann D.M., Salter A, (2004), “Impact of Innovation Technology on Engineering Problem Solving: Lessons from High Profile Public Projects,” Industrial Dynamics, Innovation and Development, 2004 Dristas, (2004) “Design Operators.” Thesis. Massachusetts Institute of Technology, Cambridge, MA, 2004 Friedman, M, (2002), Gehry Talks: Architecture + Practice, Universe Publishing, New York, NY, 2002 Kolarevic, B, (2003), Architecture in the Digital Age: Design and Manufacturing, Spon Press, London, UK, 2003 Opas J, Bochnick H, Tuomi J, (1994), “Manufacturability Analysis as a Part of CAD/CAM Integration”, Intelligent Systems in Design and Manufacturing, 261-292 Rudolph S, Alber R, (2002), “An Evolutionary Approach to the Inverse Problem in Rule-Based Design Representations”, Artificial Intelligence in Design ’02, 329-350 Rich M, (1989), Digital Mockup, American Institute of Aeronautics and Astronautics, Reston, VA, 1989 Schön, D., The Reflective Practitioner: How Professional Think in Action. Basic Books. 1983 Shelden, D, (2003), “Digital Surface Representation and the Constructability of Gehry’s Architecture.” Diss. Massachusetts Institute of Technology, Cambridge, MA, 2003 Smithers T, Conkie A, Doheny J, Logan B, Millington K, (1989), “Design as Intelligent Behaviour: An AI in Design Thesis Programme”, Artificial Intelligence in Design, 293-334 Smithers T, (2002), “Synthesis in Designing”, Artificial Intelligence in Design ’02, 3-24 Stiny, G, (1977), “Ice-ray: a note on the generation of Chinese lattice designs” Environmental and Planning B, volume 4, pp. 89-98
keywords	Digital fabrication; bilateral contouring; integral connection; complex-curve
series	SIGRADI
email
last changed	2016/03/10 09:52

_id	caadria2009_046
id	caadria2009_046
authors	Haeusler, Matthias Hank
year	2009
title	Modulations of Voxel Surfaces Through Emotional Expressions to Generate A Feedback Loop Between Private Mood and Public Image
source	Proceedings of the 14th International Conference on Computer Aided Architectural Design Research in Asia / Yunlin (Taiwan) 22-25 April 2009, pp. 173-182
doi	https://doi.org/10.52842/conf.caadria.2009.173
summary	My proposal is an investigation into the perceptual boundaries between human and architectural expression. It asks how architecture can creatively adopt human expression by using the emotions ‘displayed’ on the ‘surface face’ as a generator for displaying a surface on a voxel façade to achieve a cross-connecting perceptual change with modulations through emotion (Massumi, 2006). Through voxel facades the public with their expressed emotions will be included in the decision process of defining space, by expressing our innermost feelings through an architectural medium. Thus emotions of the individual have a platform and can be conveyed indirectly to the public, and in turn open up discussions about the state of the community through the state of the façade. An alliance of media and place in an urban context can be achieved and created, with the participation of its inhabitants, along with a new perception of how media and architecture can together shape and inform spatial relations for a feedback loop between private mood and public image.
keywords	Voxel façade; simulation; human-environment interaction; dynamic space
series	CAADRIA
email
last changed	2022/06/07 07:49

_id	ijac20064207
id	ijac20064207
authors	Hanna, Raid; Barber, Tony
year	2006
title	Digital Processes in Architectural Design:A Case Study of Computers and Creativity
source	International Journal of Architectural Computing vol. 4 - no. 2, 95-120
summary	This paper describes the results of a statistical-experimental investigation into the relationship between three variables: design cognition, the computer as a problem solving medium and 'creativity'. The hypothesis put forward suggests a directional link between the use of 'CAAD as a cognitive design medium' and 'levels' of creativity in the design process. The hypothesis was tested statistically using first year architecture students as research design subjects. In order to place the research within a context, develop a thesis and identify 'operational' measures for variables, a literature search with special emphasis on 'creativity' was conducted. The statistical findings did confirm that levels of architectural 'creativity' in the design process and in the final product were somehow affected by the use of CAAD. Ideation fluency and originality, as 'creativity' indicators, correlated positively with CAAD as a cognitive medium with coefficients 3 0.5. The statistics from subjects- group design- revealed that computers' power of visualisation, slicing and Boolean operations has helped spatial ability and could eventually help novice designers to venture and create complex objects more than they would normally do with conventional media.
series	journal
last changed	2007/03/04 07:08

_id	sigradi2006_e081d
id	sigradi2006_e081d
authors	Hecker, Douglas
year	2006
title	Dry-In House: A Mass Customized Affordable House for New Orleans
source	SIGraDi 2006 - [Proceedings of the 10th Iberoamerican Congress of Digital Graphics] Santiago de Chile - Chile 21-23 November 2006, pp. 359-362
summary	Dry-in house is a mass customized affordable housing system proposed for the reconstruction of New Orleans. The dry-in House gets the owner back to their home site quickly while providing the infrastructure an occupant needs (shelter, water, electricity). The owner is supplied with an inhabitable shell that is customizable before it is fabricated as well as onsite as the project is “fitted out” over time. The key concept is to allow families to participate in the design of their customized homes and to get people back to their home sites as quickly as possible and to give them the opportunity to finish and further customize their home over time. The project addresses inefficiencies and redundancies in emergency housing currently provided by FEMA. Primarily the dry-in House as its name implies provides a timely dried-in space which doubles as a customized infrastructure for the reconstruction of homes and neighborhoods. The project is designed to meet the $59,000 life cycle cost of the presently provided temporary housing, the notorious “FEMA Trailer”. However, the Dry-in House provides a solution that: a) Is permanent rather than temporary. The house will be finished and further customized over time rather than disposed of. b) Reoccupies the owner’s home site rather than a “FEMA ghetto” keeping the community together and functioning. c) Is mass customized rather than mass-standardized allowing the owner to have input on the design of their home. The design is a “starter home” rather than an inflexible and over-determined solution. This also has the benefit of giving variation to the reconstruction of New Orleans as opposed to the monotony of mass-production. d) Allows the owners to further customize their home over time with additional exterior finishes and the subdivision and fit out of the interior. By utilizing plate truss technology and associated parametric modeling software, highly customized trusses can be engineered and fabricated at no additional cost as compared to off-the-shelf trusses. This mass customization technology is employed to create the building section of each individual’s house. The truss is not used in its typical manner, spanning over the house; rather, it is extruded in section to form the house itself (roof, wall, and floor). Dry-in House exploits this building technology to quickly rebuild communities in a sensible manner. It allows for an increased speed of design and construction and most importantly it involves the owner in this process. The process has other benefits like reducing waste not only because it replaces the FEMA trailer which is expensive and disposable but also since the components are prefabricated there is more precision and also quality. The Dry-in House allows the owner-designer to “draw” the section of their new home providing them with a unique design and a sense of belonging and security. The design of the section of the house also provides them with spatial configurations customized relative to site conditions, program etc... Because of the narrow lot configuration of New Orleans, the design maximizes the roof as a source for natural ventilation and light for the interior of the house. In addition, the house is one room deep providing cross ventilation in all rooms minimizing reliance on artificial mechanical systems. The timely and efficient off site fabrication of building sections facilitate larger concentrations of volunteers on site at one time, thereby promoting a greater collective spirit among the community and volunteer workforce, a therapeutic event for the community as they participate in the rebuilding of their homes and city. With individualized building sections arriving on site, the construction process is imagined to be more akin to a barn raising, making possible the drying in of multiple houses in less than one day.
keywords	mass customization; digital manufacturing; affordable housing
series	SIGRADI
email
last changed	2016/03/10 09:53

_id	cf2011_p027
id	cf2011_p027
authors	Herssens, Jasmien; Heylighen Ann
year	2011
title	A Framework of Haptic Design Parameters for Architects: Sensory Paradox Between Content and Representation
source	Computer Aided Architectural Design Futures 2011 [Proceedings of the 14th International Conference on Computer Aided Architectural Design Futures / ISBN 9782874561429] Liege (Belgium) 4-8 July 2011, pp. 685-700.
summary	Architects‚Äîlike other designers‚Äîtend to think, know and work in a visual way. In design research, this way of knowing and working is highly valued as paramount to design expertise (Cross 1982, 2006). In case of architecture, however, it is not only a particular strength, but may as well be regarded as a serious weakness. The absence of non-visual features in traditional architectural spatial representations indicates how these are disregarded as important elements in conceiving space (Dischinger 2006). This bias towards vision, and the suppression of other senses‚Äîin the way architecture is conceived, taught and critiqued‚Äîresults in a disappearance of sensory qualities (Pallasmaa 2005). Nevertheless, if architects design with more attention to non visual senses, they are able to contribute to more inclusive environments. Indeed if an environment offers a range of sensory triggers, people with different sensory capacities are able to navigate and enjoy it. Rather than implementing as many sensory triggers as possible, the intention is to make buildings and spaces accessible and enjoyable for more people, in line with the objective of inclusive design (Clarkson et al. 2007), also called Design for All or Universal Design (Ostroff 2001). Within this overall objective, the aim of our study is to develop haptic design parameters that support architects during design in paying more attention to the role of haptics, i.e. the sense of touch, in the built environment by informing them about the haptic implications of their design decisions. In the context of our study, haptic design parameters are defined as variables that can be decided upon by designers throughout the design process, and the value of which determines the haptic characteristics of the resulting design. These characteristics are based on the expertise of people who are congenitally blind, as they are more attentive to non visual information, and of professional caregivers working with them. The parameters do not intend to be prescriptive, nor to impose a particular method. Instead they seek to facilitate a more inclusive design attitude by informing designers and helping them to think differently. As the insights from the empirical studies with people born blind and caregivers have been reported elsewhere (Authors 2010), this paper starts by outlining the haptic design parameters resulting from them. Following the classification of haptics into active, dynamic and passive touch, the built environment unfolds into surfaces that can act as ‚Äúmovement‚Äù, ‚Äúguiding‚Äù and/or ‚Äúrest‚Äù plane. Furthermore design techniques are suggested to check the haptic qualities during the design process. Subsequently, the paper reports on a focus group interview/workshop with professional architects to assess the usability of the haptic design parameters for design practice. The architects were then asked to try out the parameters in the context of a concrete design project. The reactions suggest that the participating architects immediately picked up the underlying idea of the parameters, and recognized their relevance in relation to the design project at stake, but that their representation confronts us with a sensory paradox: although the parameters question the impact of the visual in architectural design, they are meant to be used by designers, who are used to think, know and work in a visual way.
keywords	blindness, design parameters, haptics, inclusive design, vision
series	CAAD Futures
email
last changed	2012/02/11 19:21

_id	acadia06_555
id	acadia06_555
authors	Kudless, A., Vukcevich, I.
year	2006
title	Flexible Formwork Research (FPR)
source	Synthetic Landscapes [Proceedings of the 25th Annual Conference of the Association for Computer-Aided Design in Architecture] p. 555
doi	https://doi.org/10.52842/conf.acadia.2006.x.r8t
summary	FFR investigates the self-organization of plaster and elastic fabric to produce evocative visual and acoustic effects. Inspired by the work of the Spanish architect Miguel Fisac and his experiments with flexible concrete formwork in the 1960-70s, FFR continues this line of research by exploring aspects of pattern generation and recognition in relation to self-organized form. In line with the theme of the current exhibition, Digital Exchange, the work can be understood as a dialog between physical and digital computation. The form is a result of a negotiation between the digital manipulation of images and the physical deformations of materials under stress. Both digital and physical processes play an equal role in the final form of the plaster tiles.Reflecting on Miguel Fisac’s flexible concrete formwork, there was a desire to investigate the potential for more differentiated patterns while still using the same basic fabrication technique. This was accomplished through the use of a custom-designed script in Rhino that analyzes a given image and translates it into a field of points. These points establish areas of constraint in the elastic membrane of the mould. Through numerous physical tests, the minimum and maximum distances between constraint points was determined and these were entered into the script as limits for the point creation. If the points are too close, large wholes with very thin and weak plaster form whereas if the points are too far apart the amount of elastic deformation is so great that the weight of the plaster can cause failures to occur in the fabric mould. One of the most important aspects of the project is its resonance with the body and our natural attraction and repulsion for certain forms. Through exploring the natural self-organization of material under stress, FFR unintentionally reminds us of our own flesh. The plaster tiles resonate with our own body’s material as it sags, expands, and wrinkles in relationship with gravity, structure, and time.
series	ACADIA
email
last changed	2022/06/07 07:49

_id	ijac20064102
id	ijac20064102
authors	Lee, Jackie Chia-Hsun; Hu, Yuchang; Selker, Ted
year	2006
title	iSphere:A free-hand 3D modeling interface
source	International Journal of Architectural Computing vol. 4 - no. 1, 19-31
summary	Making 3D models should be an easy and intuitive task like free-hand sketching. This paper presents iSphere, a 24 degree of freedom 3D input device. iSphere is a dodecahedron embedded with 12 capacitive sensors for pulling-out and pressing-in manipulation on 12 control points of 3D geometries. It exhibits a conceptual 3D modeling approach for saving mental loads of low-level commands. Using analog inputs of 3D manipulation, designers are able to have high-level modeling concepts like pushing or pulling 3D surfaces. Our experiment shows that iSphere saved steps in the selection of control points in the review of menus and leading to a clearer focus on what to build instead of how to build it. Novices saved significant time learning 3D manipulation by using iSphere to making conceptual models. However, one tradeoff of the iSphere is its lack of fidelity in its analog input mechanism.
keywords	3D Input Device; Proximity Sensing; Parametric Modeling; Human-Computer Interaction
series	journal
email
more	http://www.ingentaconnect.com/content/mscp/ijac/2006/00000004/00000001/art00003
last changed	2007/03/04 07:08

_id	2006_342
id	2006_342
authors	Lyon, Eduardo
year	2006
title	Component Based Design and Digital Manufacturing - A DfM Model for Curved Surfaces Fabrication using Three Axis CNC Router
source	Communicating Space(s) [24th eCAADe Conference Proceedings / ISBN 0-9541183-5-9] Volos (Greece) 6-9 September 2006, pp. 342-350
doi	https://doi.org/10.52842/conf.ecaade.2006.342
summary	Through the use of design for manufacturing (DfM) method and looking at the relations between its potential application in architectural production and its implementation using digital manufacturing technologies, we analyze building construction processes and explore, in more detail curved surface fabrication using two dimensional cutting and three dimensional milling processes. Afterwards a DfM model for curved surfaces fabrication using three-axis computer numerical control (CNC) router is proposed. The proposed DfM model relies fundamentally in two supporting factors; the implementation of design heuristics that integrates production knowledge and the availability of some design related to production evaluation metrics. Subsequently, we test and refine the model using structured design experiences. This was accomplished by capturing new design heuristics and detecting useful evaluation metrics for production. In the final part of the research, a refined DfM model was tested in a component design case study. The case study is based on producing a curved surface module on wood for an existing proprietary component based wall system. As a summary, we conceptualize from this top-down development approach to create a design for manufacturing model that integrates design and construction in architecture, based on three possible applications fields: Design processes improvement, building production process improvement, CAD-CAM tools development. Our purpose is to provide better foundational constructs and approaches for integrating design with manufacturing in architecture.
keywords	Design for Manufacturing; Design Cognition; Digital Fabrication
series	eCAADe
email
last changed	2022/06/07 07:59

_id	acadia06_278
id	acadia06_278
authors	Mathew, Anijo
year	2006
title	Aesthetic Interaction A Model for Re-thinking the Design of Place
source	Synthetic Landscapes [Proceedings of the 25th Annual Conference of the Association for Computer-Aided Design in Architecture] pp. 278-291
doi	https://doi.org/10.52842/conf.acadia.2006.278
summary	We live in a landscape of digital information and communication. Digital technology finds pervasive application in many aspects of modern habitable spaces— environmental control systems, internet based systems for information exchange, cellular systems for instant communication, and the list goes on. In fact, recent Intel studies show that every day we encounter at least 150 different computing devices in our living environments. As computing initiatives evolve intelligent devices that work in the background of our day to day living, several questions arise about how we interact with these devices. The design of “smart” places will eventually involve the seamless integration of both the physical and virtual. Such interventions will lead to a transformation in the way we design. Architects will increasingly find themselves using the computer in design as opposed to design. Over the last few years our lab has been working on several projects, from the level of a room to the level of urban design, that use embedded interactivity and computing as part of the design. This paper describes three such projects, completed at different times, which deal with different problems and the overall impact of computing on the way the designs were developed. The description and evaluation of these projects will be used to develop a theory for the use of pragmatist aesthetics for “information interchange” within architectural design. In short, the paper will explore the evolution of Computer “Aided” Design from a model for designing architecture to a model for designing computing within architecture through aesthetic interaction.
series	ACADIA
email
last changed	2022/06/07 07:58

_id	caadria2006_269
id	caadria2006_269
authors	MATTHIAS HAASE, ALEX AMATO
year	2006
title	ND MODELLING FOR SUSTAINABLE ENVELOPES: The sustainable dimensions of envelope design
source	CAADRIA 2006 [Proceedings of the 11th International Conference on Computer Aided Architectural Design Research in Asia] Kumamoto (Japan) March 30th - April 2nd 2006, 269-276
doi	https://doi.org/10.52842/conf.caadria.2006.x.e6l
summary	Sustainable development issues are currently the driving forces in many building projects. The building envelope is critical for the architectural expression as well as large parts of the environmental performance. This study tries to investigate the advantages of multidimensional computer aided modeling and simulation for a sustainable facade design approach. A first step towards nD modeling for sustainable design is to establish a list of parameter which are used as design criteria: Environmental performance, thermal visual and acoustic comfort. Computer simulation and analysis of different building elements can help to determine the performance according to a set of design parameter. Environmental impacts due to energy consumption are an important parameter but it is believed that comfort criteria need also to be accounted for.
series	CAADRIA
email
last changed	2022/06/07 07:49

_id	caadria2006_237
id	caadria2006_237
authors	N.BILORIA, K.OOSTERHUIS, C. AALBERS
year	2006
title	DESIGN INFORMATICS: (A case based investigation into parametric design, scripting and CNC based manufacturing techniques)
source	CAADRIA 2006 [Proceedings of the 11th International Conference on Computer Aided Architectural Design Research in Asia] Kumamoto (Japan) March 30th - April 2nd 2006, 237-244
doi	https://doi.org/10.52842/conf.caadria.2006.x.q9e
summary	The research paper exemplifies a novel information integrated design technique developed at ONL (Oosterhuis and Lenard), Netherlands, specifically appropriated for envisaging complex geometric forms. The ‘informed design technique’, apart from being highly instrumental in conceptualizing and generating the geometric component constituting architectural form in a parametric manner, is also efficiently utilized for precise computer aided manufacturing and construction of the speculated form. Geometric complexities inherent in contemporary architectural constructs and the time spent in appropriation of such topologies, fueled the ‘informed design’ approach, which caters to issues of timely construction, precision oriented design and production (visual and material) and parametric modeling attuned to budgetary fluctuations. This design-research approach has been tested and deployed by ONL, for conceiving ‘the Acoustic Barrier’ project, Utrecht Leidsche Rijn in the Netherlands and is treated as a generic case for exemplifying the ‘informed design’ technique in this research paper. The design methodology encourages visualizing architectural substantiations from a systems perspective and envisages upon a rule based adaptive systems approach involving extrapolation of contextual dynamics/ground data in terms of logical ‘rules’. These rules/conditionalities form the basis for spawning parametric logistics to be mapped upon geometric counterparts exemplifying the conception. The simulated parametric relations bind dimensional aspects (length, width, height etc.) of the geometric construct in a relational manner, eventually culminating in a 3D spatial envelope. This evolved envelope is subsequently intersected with a ‘parametric spatio-constructive grid’, creating specific intersecting points between the two. The hence extorted ‘point cloud’ configuration serves as a generic information field concerning highly specific coordinates, parameters and values for each individual point/constructive node it embodies. The relations between these points are directly linked with precise displacements of structural profiles and related scaling factors of cladding materials. Parallel to this object oriented modeling approach, a detailed database (soft/information component) is also maintained to administer the relations between the obtained points. To be able to derive constructible structural and cladding components from the point cloud configuration customized Scripts (combination of Lisp and Max scripts) process the point cloud database. The programmed script-routines, iteratively run calculations to generate steel-wire frames, steel lattice-structure and cladding panels along with their dimensions and execution drawing data. Optimization-routines are also programmed to make rectifications and small adjustments in the calculated data. This precise information is further communicated with CNC milling machines to manifest complex sectional profiles formulating the construct hence enabling timely and effective construction of the conceptualized form.
series	CAADRIA
email
last changed	2022/06/07 07:49

_id	ddss2006-hb-359
id	DDSS2006-HB-359
authors	P.P. van Loon and E. Wilms
year	2006
title	An Urban Decision Room Based on Mathematical Optimisation - A pilot study supporting complex urban decision questions
source	Van Leeuwen, J.P. and H.J.P. Timmermans (eds.) 2006, Innovations in Design & Decision Support Systems in Architecture and Urban Planning, Dordrecht: Springer, ISBN-10: 1-4020-5059-3, ISBN-13: 978-1-4020-5059-6, p. 359-374
summary	In general the Urban Decision Room is an interactive computer system based around a digital model for the simulation of complex urban decision questions. Such questions involve various parties with often differing interests. The UDR can assist in finding collective solutions. The UDR is a useful instrument for making the great variety in interests and ideas of the participants manageable. Furthermore, insight is quickly and clearly provided into the results. This enhances the efficiency and effectiveness of processes of urban development. A pilot of the Urban Decision Room based on mathematical optimisation has been made for Schieoevers, an industrial area on the bank of the river Schie to the south of Delft. This pilot is based on a feasibility study for a new urban development in this area which has been carried out by a consultancy firm (Adecs BV) under commission from the municipality of Delft.
keywords	Decision support system, Urban planning, Design optimisation
series	DDSS
last changed	2006/08/29 12:55

_id	cf2011_p115
id	cf2011_p115
authors	Pohl, Ingrid; Hirschberg Urs
year	2011
title	Sensitive Voxel - A reactive tangible surface
source	Computer Aided Architectural Design Futures 2011 [Proceedings of the 14th International Conference on Computer Aided Architectural Design Futures / ISBN 9782874561429] Liege (Belgium) 4-8 July 2011, pp. 525-538.
summary	Haptic and tactile sensations, the active or passive exploration of our built surroundings through our sense of touch, give us a direct feeling and detailed information of space, a sense of architecture (Pallasmaa 2005). This paper presents the prototype of a reactive surface system, which focuses its output on the sense of touch. It explains how touch sensations influence the perception of architecture and discusses potential applications that might arise from such systems in the future. A growing number of projects demonstrate the strong impact of interaction design on the human senses and perception. They offer new ways of sensing and experiencing architectural space. But the majority of these interaction concepts focus on visual and auditory output-effects. The sense of touch is typically used as an input generator, but neglected as as a potential receiver of stimuli. With all the possibilities of sensors and micro-devices available nowadays, there is no longer a technical reason for this. It is possible to explore a much wider range of sense responding projects, to broaden the horizon of sensitive interaction concepts (Bullivant 2006). What if the surfaces of our surroundings can actively change the way it feels to touch them? What if things like walls and furniture get the ability to interactively respond to our touch? What new dimensions of communication and esthetic experience will open up when we conceive of tangibility in this bi-directional way? This paper presents a prototype system aimed at exploring these very questions. The prototype consists of a grid of tangible embedded cells, each one combining three kinds of actuators to produce divergent touch stimuli. All cells can be individually controlled from an interactive computer program. By providing a layering of different combinations and impulse intensities, the grid structure enables altering patterns of actuation. Thus it can be employed to explore a sort of individual touch aesthetic, for which - in order to differentiate it from established types of aesthetic experiences - we have created the term 'Euhaptics' (from the Greek ŒµœÖ = good and Œ¨œÄœÑœâ = touch, finger). The possibility to mix a wide range of actuators leads to blending options of touch stimuli. The sense of touch has an expanded perception- spectrum, which can be exploited by this technically embedded superposition. The juxtaposed arrangement of identical multilayered cell-units offers blending and pattern effects of different touch-stimuli. It reveals an augmented form of interaction with surfaces and interactive material structures. The combination of impulses does not need to be fixed a priori; it can be adjusted during the process of use. Thus the sensation of touch can be made personally unique in its qualities. The application on architectural shapes and surfaces allows the user to feel the sensations in a holistic manner ‚Äì potentially on the entire body. Hence the various dimensions of touch phenomena on the skin can be explored through empirical investigations by the prototype construction. The prototype system presented in the paper is limited in size and resolution, but its functionality suggests various directions of further development. In architectural applications, this new form of overlay may lead to create augmented environments that let inhabitants experience multimodal touch sensations. By interactively controlling the sensual patterns, such environments could get a unique ‚Äútouch‚Äù for every person that inhabit them. But there may be further applications that go beyond the interactive configuration of comfort, possibly opening up new forms of communication for handicapped people or applications in medical and therapeutic fields (Grunwald 2001). The well-known influence of touch- sensations on human psychological processes and moreover their bodily implications suggest that there is a wide scope of beneficial utilisations yet to be investigated.
keywords	Sensitive Voxel- A reactive tangible surface
series	CAAD Futures
email
last changed	2012/02/11 19:21

_id	2006_316
id	2006_316
authors	Stouffs, Rudi and Mark Wieringa
year	2006
title	The generation of Chinese ice-ray lattice designs on 3D surfaces
source	Communicating Space(s) [24th eCAADe Conference Proceedings / ISBN 0-9541183-5-9] Volos (Greece) 6-9 September 2006, pp. 316-319
doi	https://doi.org/10.52842/conf.ecaade.2006.316
summary	We revisit Stiny’s ice-ray grammar and adapt its shape rules, including additional rules for augmenting a polygon by inscribing a triangular shape, to apply to twisted surfaces. We describe the constructive process of rule application for twisted polygons, shortly describe the implementation of the grammar, and illustrate its use in the design of a façade, the shape of which is defined as a twisted polygon.
keywords	Design generation; shape grammars; ice-ray lattice designs, twisted surfaces
series	eCAADe
email
last changed	2022/06/07 07:56

For more results click below: