Cumincad : CUMINCAD Papers : Search Results

CumInCAD is a Cumulative Index about publications in Computer Aided Architectural Design
supported by the sibling associations ACADIA, CAADRIA, eCAADe, SIGraDi, ASCAAD and CAAD futures

PDF papers
References

Hits 1 to 20 of 460

Reformat results as: short short into frame detailed detailed into frame

_id	acadia12_305
id	acadia12_305
authors	Kock, Jeffrey ; Bradley, Benjamin ; Levelle, Evan
year	2012
title	The Digital-Physical Feedback Loop: A Case Study
source	ACADIA 12: Synthetic Digital Ecologies [Proceedings of the 32nd Annual Conference of the Association for Computer Aided Design in Architecture (ACADIA) ISBN 978-1-62407-267-3] San Francisco 18-21 October, 2012), pp. 305-314
doi	https://doi.org/10.52842/conf.acadia.2012.305
summary	Kukje Art Center, Seoul’s new gallery designed by SO-IL, features a totally bespoke chainmail mesh system (submission note: the authors are not affiliated with SO-IL). A single sheet of complex-curved, tensioned mesh, made up of interlocking 40mm diameter stainless steel rings, wraps the building. This paper discusses the stages of a feedback loop process employed by the authors to refine a digital model of the mesh. The mesh’s perimeter attachment system does not prescribe ring locations, allowing the mesh to form find for itself during installation. As a result, the digital model must capture the behavioral tendencies of the mesh as it negotiates the building’s geometry. Paramount in meeting this challenge was the use of physical mockups. At each stage of the feedback loop process, the working digital model was used to develop a physical mockup of increased scale and complexity, and this mockup was used to refine the digital model. Ultimately, the model output of a mesh relaxation algorithm was used as the basis for engineering simulations and predictions of the mesh vertical ringcount needed at specific locations around the building. Mesh vertical ringcount predictions are validated relative to a 1:1 mockup and the installed Kukje Art Center mesh.
keywords	minimal surface , chainmail mesh , form finding , dynamic relaxation , finite element analysis , feedback loop , tensioned fabric , physical mockup , bespoke cladding , Kukje , Seoul
series	ACADIA
type	normal paper
email
last changed	2022/06/07 07:51

_id	acadia12_199
id	acadia12_199
authors	Beorkrem, Chris ; Corte, Dan
year	2012
title	Zero-Waste, Flat-Packed, Tri-Chord Truss: Continued Investigations of Structural Expression in Parametric Design"
source	ACADIA 12: Synthetic Digital Ecologies [Proceedings of the 32nd Annual Conference of the Association for Computer Aided Design in Architecture (ACADIA) ISBN 978-1-62407-267-3] San Francisco 18-21 October, 2012), pp. 199-208
doi	https://doi.org/10.52842/conf.acadia.2012.199
summary	The direct and rapid connections between scripting, modeling and prototyping allow for investigations of computation in fabrication. The manipulation of planar materials with two-dimensional CNC cuts can easily create complex and varied forms, volumes, and surfaces. However, the bulk of research on folding using CNC fabrication tools is focused upon surfaces, self-supporting walls and shell structures, which do not integrate well into more conventional building construction models. This paper attempts to explain the potential for using folding methodologies to develop structural members through a design-build process. Conventional building practice consists of the assembly of off-the-shelf parts. Many times, the plinth, skeleton, and skin are independently designed and fabricated, integrating multiple industries. Using this method of construction as an operative status quo, this investigation focused on a single structural component: the truss. Using folding methodologies and sheet steel to create a truss, this design investigation employed a recyclable and prolific building material to redefine the fabrication of a conventional structural member. The potential for using digital design and two-dimensional CNC fabrication tools in the design of a foldable truss from sheet steel is viable in the creation of a flat-packed, minimal waste structural member that can adapt to a variety of aesthetic and structural conditions. Applying new methods to a component of the conventional ‘kit of parts’ allowed for a novel investigation that recombines zero waste goals, flat-packing potential, structural expression and computational processes. This paper will expand (greatly) upon previous research into bi-chord truss designs, developing a tri-chord truss, which is parametrically linked to its structural moment diagram. The cross section of each truss is formed based on the loading condition for each beam. This truss design has been developed through a thorough series of analytical models and tests performed digitally, to scale and in full scale. The tri-chord truss is capable of resisting rotational failures well beyond the capacity of the bi-chord designs previously developed. The results are complex, and elegant expressions of structural logics embodied in a tightly constrained functional design.
keywords	Parametric Design , Structural Expression , Material constraints
series	ACADIA
type	normal paper
email
last changed	2022/06/07 07:54

_id	sigradi2012_107
id	sigradi2012_107
authors	Carrión, Awilda Rodríguez
year	2012
title	Scalable Explorations
source	SIGraDi 2012 [Proceedings of the 16th Iberoamerican Congress of Digital Graphics] Brasil - Fortaleza 13-16 November 2012, pp. 449-452
summary	Authoring environments should strive for effortless navigation, traversing the space-scale virtual space in order to comprehend relationships between distinct elements, provide landmark or reference objects to keep the user’s orientation and perceptual cues that will enhance direction and depth perception. This paper will explore how the dynamic nature of 3-D virtual environments can provide new generations with powerful tools to explore disparate spatial scales, expand the modeling information and give them the ability to manipulate conceptually critical information that is governed by various scale parameters.
keywords	BIM; virtual space; scale; urban space
series	SIGRADI
email
last changed	2016/03/10 09:48

_id	acadia12_139
id	acadia12_139
authors	Erioli, Alessio ; Zomparelli, Alessandro
year	2012
title	Emergent Reefs
source	ACADIA 12: Synthetic Digital Ecologies [Proceedings of the 32nd Annual Conference of the Association for Computer Aided Design in Architecture (ACADIA) ISBN 978-1-62407-267-3] San Francisco 18-21 October, 2012), pp. 139-148
doi	https://doi.org/10.52842/conf.acadia.2012.139
summary	The Emergent Reefs project thrives on the potential that emerge from a coherent utilization of the environment’s inherent ecological structure for its own transformation and evolution, using an approach based on digitally simulated ecosystems and sparkled by the possibilities and potential of large-scale 3D printing technology. Considering tourism as an inevitable vector of environmental change, the project aims to direct its potential and economic resources towards a positive transformation, providing a material substrate for the human-marine ecosystem integration with the realization of spaces for an underwater sculpture exhibition. Such structures will also provide a pattern of cavities which, expanding the gradient of microenvironmental conditions, break the existing homogeneity in favor of systemic heterogeneity, providing the spatial and material preconditions for the repopulation of marine biodiversity. Starting from a digital simulation of a synthetic local ecosystem, a generative technique based on multi-agent systems and continuous cellular automata (put into practice from the theoretical premises in Alan Turing’s paper “The Chemical basis of Morphogenesis” through reaction-diffusion simulation) is implemented in a voxel field at several scales giving the project a twofold quality: the implementation of reaction diffusion generative strategy within a non-isotropic 3-dimensional field and integration with the large-scale 3D printing fabrication system patented by D-Shape®. Out of these assumptions and in the intent of exploiting the expressive and tectonic potential of such technology, the project has been tackled exploring voxel-based generative strategies. Working with a discrete lattice eases the simulation of complex systems and processes across multiple scales (including non-linear simulations such as Computational Fluid-Dynamics) starting from local interactions using, for instance, algorithms based on cellular automata, which then can be translated directly to the physical production system. The purpose of Emergent-Reefs is to establish, through strategies based on computational design tools and machine-based fabrication, seamless relationships between three different aspects of the architectural process: generation, simulation and construction, which in the case of the used technology can be specified as guided growth.
keywords	emergence , reef , underwater , 3D printing , ecology , ecosystem , CFD , agency , architecture , tourism , culture , Open Source
series	ACADIA
type	normal paper
email
last changed	2022/06/07 07:55

_id	ecaade2012_82
id	ecaade2012_82
authors	Mohammad, Kareem El Sayed; Hanafi, Mohammad Assem; Nasr, Mohammad
year	2012
title	A Closer Perspective on Fabrication Realities
source	Achten, Henri; Pavlicek, Jiri; Hulin, Jaroslav; Matejovska, Dana (eds.), Digital Physicality - Proceedings of the 30th eCAADe Conference - Volume 2 / ISBN 978-9-4912070-3-7, Czech Technical University in Prague, Faculty of Architecture (Czech Republic) 12-14 September 2012, pp. 169-179
doi	https://doi.org/10.52842/conf.ecaade.2012.2.169
wos	WOS:000330320600017
summary	Digital Fabrication has arguably stirred the return of the architect to the long-held position as a master builder. The close engagement with materials offered by the digital fabrication technologies places necessary limitations and calls the architects for a deeper understanding of and awareness about the fabrication realities during the design process. The research conducted uses parametric modeling for the alteration of the design according to a wide range of infl uences, one of which is fabrication. This paper offers a close perspective on some fabrication necessities and limitations that emerged through the manufacturing of a number of scaled models of a parametrically designed shed and a full scale pavilion. The scope of this work falls into the realm of physical testing, tolerance, structure and assembly. It also points out the fabrication parameters that were part of the digital setting used to create the physical models. The paper argues that craft is still practically alive when deploying digital technologies as it has been ever present in the pre-digital era.
keywords	Digital fabrication; tolerances; parametric design; assembly; Laser cutting
series	eCAADe
email
last changed	2022/06/07 07:58

_id	acadia12_333
id	acadia12_333
authors	Poulsen, Esben Skouboe ; Andersen, Hans Jørgen
year	2012
title	Reactive Light Design in the ""Laboratory of the Street"" Esben Skouboe Poulsen, Hans Jørgen Andersen"
source	ACADIA 12: Synthetic Digital Ecologies [Proceedings of the 32nd Annual Conference of the Association for Computer Aided Design in Architecture (ACADIA) ISBN 978-1-62407-267-3] San Francisco 18-21 October, 2012), pp. 333-342
doi	https://doi.org/10.52842/conf.acadia.2012.333
summary	This paper presents and discusses results related to a full-scale responsive urban lighting experiment and introduces a light design methodology inspired by reactive control strategies in robot systems. The experiment investigates how human motion intensities can be used as input to light design in a reactive system. Using video from 3 thermal cameras and computer vision analysis; people’s flow patterns were monitored and send as input into a reactive light system. Using physical as well as digital models 4 different light scenarios is designed and tested in full-scale. Results show that people on the square did not engage in the changing illumination and often they did not realized that the light changed according to their presence. However from the edge of the square people observed the light patterns “painted” on the city square, as such people became actors on the urban stage, often without knowing. Furthermore did the experiment showcase power savings up to 90% depending on the response strategy.
keywords	Responsive environments , Architectural Lighting , Interaction , Realtime response , Computer vision
series	ACADIA
type	normal paper
email
last changed	2022/06/07 08:00

_id	ijac201210307
id	ijac201210307
authors	Willmann, Jan; Federico Augugliaro, Thomas Cadalbert, et al.
year	2012
title	Aerial Robotic Construction Towards a New Field of Architectural Research
source	International Journal of Architectural Computing vol. 10 - no. 3, 439-459
summary	This paper takes a first step in characterizing a novel field of architectural research - aerial robotic construction (ARC) - where aerial robotics is used not only for construction, but as a guiding principle in the design and fabrication process. Featuring autonomous flying vehicles that lift small building elements and position them according to a precise digital blueprint, ARC offers a comprehensive new approach to architecture research and technology. Developed by the research groups of Gramazio & Kohler and Raffaello D'Andrea at ETH Zurich, ARC offers unique advantages over traditional approaches to building: it does not require scaffolding, it is easily scalable, and it offers digital integration and informational oversight across the entire design and building process. This paper considers 1) research parameters for the individual components of ARC (such as module design, connection methodologies, vehicle cooperation, and construction sequencing/synchronization), and 2) the architectural implications of integrating these discrete components into a systemic, unifying process at the earliest stages of design. Fidelity between the design concept and the full-scale construction is of particular concern.
series	journal
last changed	2019/05/24 09:55

_id	ecaade2012_310
id	ecaade2012_310
authors	Kotsopoulos, Sotirios D; Casalegno, Federico; Hsiung, Bob; Graybill, Wesley
year	2012
title	A Prototype Hut for the Post-Digital Age
source	Achten, Henri; Pavlicek, Jiri; Hulin, Jaroslav; Matejovska, Dana (eds.), Digital Physicality - Proceedings of the 30th eCAADe Conference - Volume 2 / ISBN 978-9-4912070-3-7, Czech Technical University in Prague, Faculty of Architecture (Czech Republic) 12-14 September 2012, pp. 317-326
doi	https://doi.org/10.52842/conf.ecaade.2012.2.317
wos	WOS:000330320600032
summary	The paper presents how the latest advances in autonomous building management and electrically activated materials affect the design, production, and operation of residential buildings. The innovative features of an elementary prototype house, which is at the fi nal stage of construction in Trento, N. Italy, are discussed with a view to expose the opportunities and the problems that these new technological developments pose to design research.
keywords	Electrically activated materials; model-based control; design; implementation; operation
series	eCAADe
email
last changed	2022/06/07 07:51

_id	sigradi2012_272
id	sigradi2012_272
authors	Amindarbari, Reza
year	2012
title	Morphological indicators of solar exposure
source	SIGraDi 2012 [Proceedings of the 16th Iberoamerican Congress of Digital Graphics] Brasil - Fortaleza 13-16 November 2012, pp. 414-418
summary	This paper investigates the relation between the shading condition and geometrical configuration of neighborhood-scale developments. It introduces a straightforward method for measuring shadow areas casted on buildings’ roofs and facades – in urban areas – using digital 3D models. Employing this method for measuring shadow areas in nine neighborhoods in Jinan, China, at six different time points on summer and winter solstices – a total of 54 sample measurements – this study develops two regression models that reveal the significant dependency of the in-shadow percentage of buildings’ façade and roof areas to the building volume density (BVD) and height irregularity (HI) of the urban fabric.
keywords	urban form, geometrical configuration, solar exposure, shadow area
series	SIGRADI
email
last changed	2016/03/10 09:47

_id	acadia12_439
id	acadia12_439
authors	As, Imdat ; Angelico, Maria
year	2012
title	Crowdsourcing Architecture: A Disruptive Model in Architectural Practice
source	ACADIA 12: Synthetic Digital Ecologies [Proceedings of the 32nd Annual Conference of the Association for Computer Aided Design in Architecture (ACADIA) ISBN 978-1-62407-267-3] San Francisco 18-21 October, 2012), pp. 439-443
doi	https://doi.org/10.52842/conf.acadia.2012.439
summary	This paper discusses the use of crowdsourcing as a new approach for architectural design acquisition. We will give an overview of the concept of crowdsourcing, and elaborate on its particular application in architecture via concrete projects executed on Arcbazar, a firstof- its-kind crowdsourcing platform for architectural design services. We argue that online crowdsourcing platforms can have an immense impact on smaller-scale design challenges, e.g., home remodeling projects and landscape and interior design challenges, and can potentially carry these often neglected projects into the architectural design sphere. In this paper we will discuss the methods and techniques of architectural crowdsourcing and illustrate the processes and outcomes through a series of projects: a remodeling project for a closet; an interior design challenge for a dining space; and a layout problem for an apartment complex. We will then evaluate the protocol and outcome of architectural crowdsourcing, and convey the professional and popular media response to this new method of architectural design acquisition.
keywords	crowdsourcing , competitions , networking , interaction , collaboration
series	ACADIA
type	panel paper
email
last changed	2022/06/07 07:54

_id	sigradi2012_291
id	sigradi2012_291
authors	Braida, Frederico; Marques, Aline Calazans; Pedroso, Emmanuel Sá Resende; Lima, Fernando Tadeu de Araújo
year	2012
title	O papel das impressoras 3D nas diversas etapas do projeto [O papel das impressoras 3D nas diversas etapas do projeto The 3D printer paper at various stages of project]
source	SIGraDi 2012 [Proceedings of the 16th Iberoamerican Congress of Digital Graphics] Brasil - Fortaleza 13-16 November 2012, pp. 580-583
summary	This article aims to address the use of 3D printers in the stages of design, development and final presentation in projects of architecture and urbanism. To evaluate the performance of 3D printers, we emphasize in each of these stages of the project, the representational demands and cognitive processes involved as well as analytical categories taken as cost, running time, accuracy and level finish, the representation of materials, scale and size of three-dimensional models and possibilities for intervention in the models themselves.
keywords	Impressoras 3D; Prototipagem rápida; Projeto; Fabricação Digital; Modelagem tridimensional
series	SIGRADI
email
last changed	2016/03/10 09:47

_id	acadia12_127
id	acadia12_127
authors	Burry, Jane ; Burry, Mark ; Tamke, Martin ; Thomsen, Mette Ramsgard ; Ayres, Phil ; Leon, Alex Pena de ; Davis, Daniel ; Deleuran, Abders ; Nielson, Stig ; Riiber, Jacob
year	2012
title	Process Through Practice: Synthesizing a Novel Design and Production Ecology
source	ACADIA 12: Synthetic Digital Ecologies [Proceedings of the 32nd Annual Conference of the Association for Computer Aided Design in Architecture (ACADIA) ISBN 978-1-62407-267-3] San Francisco 18-21 October, 2012), pp. 127-138
doi	https://doi.org/10.52842/conf.acadia.2012.127
summary	This paper describes the development of a design and prototype production system for novel structural use of networked small components of wood deploying elastic and plastic bending. The design process engaged with a significant number of different overlapping and interrelated design criteria and parameters, a high level of complexity, custom component geometry and the development of digital tools and procedures for real time feedback and productivity. The aims were to maximize learning in the second order cybernetic sense through empirical experience from analogue modeling, measurement and digital visual feedback and to capture new knowledge specifically regarding intrinsic material behavior applied and tested in a heterogeneous networked context. The outcome was a prototype system of design ideation, conceptualization, development and production that integrated real time material performance simulation and feedback. The outcome was amplified through carrying out the research over a series of workshops with distinct foci and participation. Two full scale demonstrators have so far been constructed and exhibited as outputs of the process.
keywords	Material behavior , Complex modeling feedback , progressive synthetic learning
series	ACADIA
type	normal paper
email
last changed	2022/06/07 07:54

_id	acadia12_325
id	acadia12_325
authors	Chronis, Angelos ; Tsigkari, Martha ; Davis, Adam ; Aish, Francis
year	2012
title	Design Systems, Ecology, and Time Angelos Chronis, Martha Tsigkari, Adam Davis, Francis Aish"
source	ACADIA 12: Synthetic Digital Ecologies [Proceedings of the 32nd Annual Conference of the Association for Computer Aided Design in Architecture (ACADIA) ISBN 978-1-62407-267-3] San Francisco 18-21 October, 2012), pp. 325-332
doi	https://doi.org/10.52842/conf.acadia.2012.325
summary	Discussion of architecture in ecological terms usually focuses on the spatial and material dimensions of design practice. Yet there is an equally critical temporal dimension in ecology that is just as relevant to design. At the micro scale is the question of 'real time' feedback from our design systems. At the macro scale is the issue of sustainability, in other words long term -- and potentially disastrous -- feedback from terrestrial ecosystems. In between are numerous different units for quantizing time in design and computation. In this paper, we examine some of these units -- 'real time', 'design time', 'development time' -- to suggest how they interact with the ecology of design technology and practice. We contextualize this discussion by reference to relevant literature from the field of ecology and to our work applying custom design and analysis tools on architectural projects within a large interdisciplinary design practice.
keywords	real time feedback , performance driven design , integration
series	ACADIA
type	normal paper
email
last changed	2022/06/07 07:54

_id	acadia12_295
id	acadia12_295
authors	Dierichs, Karola ; Menges, Achim
year	2012
title	Functionally Graded Aggregate Structures: Digital Additive Manufacturing With Designed Granulates
source	ACADIA 12: Synthetic Digital Ecologies [Proceedings of the 32nd Annual Conference of the Association for Computer Aided Design in Architecture (ACADIA) ISBN 978-1-62407-267-3] San Francisco 18-21 October, 2012), pp. 295-304
doi	https://doi.org/10.52842/conf.acadia.2012.295
summary	In recent years, loose granulates have come to be investigated as architectural systems in their own right. They are defined as large numbers of elements in loose contact, which continuously reconfigure into variant stable states. In nature they are observed in systems like sand or snow. In architecture, however, they were previously known only from rare vernacular examples and geoengineering projects, and are only now being researched for their innate material potentials. Their relevance for architecture lies in being entirely reconfigurable and in allowing for structures that are functionally graded on a macro level. Hence they are a very relevant yet unexplored field within architectural design. The research presented here is focused on the potential of working with designed granulates, which are aggregates where the individual particles are designed to accomplish a specific architectural effect. Combining these with the use of a computer-controlled emitter-head, the process of pouring these aggregate structures can function as an alternative form of 3D printing or digital additive manufacturing, which allows both for instant solidification, consequent reconfiguration, and graded material properties. In its first part, the paper introduces the field of research into aggregate architectures. In its second part, the focus is laid on designed aggregates, and an analytical design tool for the individual grains is discussed. The third part presents research conducted into the process of additive manufacturing with designed granulates. To conclude, further areas of investigation are outlined especially with regard to the development of the additive manufacturing of functionally graded architectural structures. The potentials of the methodologies developed in this process are shown through the fabrication of a full-scale installation. By integrating material, fabrication, and design constraints into a streamlined computational methodology, the process also serves as a model for a more intuitive production workflow, expanding the understanding of glass as a material with wide-ranging possibilities for a more performative architecture.
keywords	Aggregate Architectures , Digital Additive Manufacturing , Functionally Graded Materials
series	ACADIA
type	normal paper
email
last changed	2022/06/07 07:55

_id	ecaade2012_60
id	ecaade2012_60
authors	Dierichs, Karola; Menges Achim
year	2012
title	Material and Machine Computation of Designed Granular Matter: Rigid-Body Dynamics Simulations as a Design Tool for Robotically-Poured Aggregate Structures Consisting of Polygonal Concave Particles
source	Achten, Henri; Pavlicek, Jiri; Hulin, Jaroslav; Matejovska, Dana (eds.), Digital Physicality - Proceedings of the 30th eCAADe Conference - Volume 2 / ISBN 978-9-4912070-3-7, Czech Technical University in Prague, Faculty of Architecture (Czech Republic) 12-14 September 2012, pp. 711-719
doi	https://doi.org/10.52842/conf.ecaade.2012.2.711
wos	WOS:000330320600076
summary	Loose granulates are a relevant yet rarely deployed architectural material system. Their significance lies in their capacity to combine fluid-like amorphousness with solid-like rigidity, resulting in potential architectural structures capable of continuous reconfi guration. In addition aggregates allow for functional grading. Especially if custom designed concave particles are used, full-scale architectural structures can be poured using a six-axis industrial robot, combining the precise travel of the emitter-head with the self-organizational capacity of granular substances. In this context, the paper proposes Rigid-Body Dynamics (RBD) simulations as a design-tool for the robotic pouring of loose granular structures. The notions of material and machine computation are introduced and RBD is explained in greater detail. A set of small tests is conducted to investigate the advantages and disadvantages of a specifi c RBD software. Conclusively, further areas of research are outlined.
keywords	Material and machine computation; aggregate architectures; designed granulates; robotic pouring; Rigid-Body Dynamics
series	eCAADe
email
last changed	2022/06/07 07:55

_id	caadria2012_107
id	caadria2012_107
authors	Gerber, David and A. Senel Solmaz
year	2012
title	PARA-Typing the making of difference: Associative parametric design methodologies for teaching the prototyping of material affect
source	Proceedings of the 17th International Conference on Computer Aided Architectural Design Research in Asia / Chennai 25-28 April 2012, pp. 233–242
doi	https://doi.org/10.52842/conf.caadria.2012.233
summary	PARA-Typing the Making of Difference presents design research and instruction into the use of constraint based digital and analogue modelling techniques and the development of associative parametric models to simulate highly differentiated fabricated form. These design research projects were conceived as manual analogue generative processes for prototyping modularity and serial differentiation. Then through associative parametric design technologies and methodologies, modular fields were design explored and developed in concert with material properties and constraints. Utilising digital fabrication full-scale installations were designed, manufactured, and constructed as tiled walls that created differentiated space within site-specific configurations.
keywords	Generative design; parametric modelling; prototyping; digital fabrication; tectonics
series	CAADRIA
email
last changed	2022/06/07 07:51

_id	ijac201210403
id	ijac201210403
authors	Gerber, David J.
year	2012
title	PARA-Typing Informing Form and the Making of Difference
source	International Journal of Architectural Computing vol. 10 - no. 4, 501-520
summary	This paper presents design research and instruction into the use of constraint based digital and analogue modelling techniques and the development of associative parametric models to simulate highly differentiated fabricated form. One set of these design research projects were conceived as manual analogue generative processes for prototyping modularity and serial differentiation.Then through parametric design techniques, modular aggregations were design explored and developed in concert with material properties and constraints. Utilizing digital fabrication full-scale installations were designed, manufactured, and for site-specific configurations. A second set of projects provides an extension of the design instruction that includes the integration of performance criteria into these design objectives.The objectives of the research are to present benefits and limitations of the incorporation of parametric design, performance analysis, and prototyping techniques in comprehensive studio instruction.The paper discusses the resultant informed materialized difference and the impacts on achieving reinforced and hands on learning objectives.
keywords	Generative design; parametric modelling; prototyping; digital fabrication; design pedagogy; performative design
series	journal
last changed	2019/05/24 09:55

_id	acadia12_169
id	acadia12_169
authors	Helm, Volker ; Ercan, Selen ; Gramazio, Fabio ; Kohler, Matthias
year	2012
title	In-Situ Robotic Construction: Extending the Digital Fabrication Chain in Architecture
source	ACADIA 12: Synthetic Digital Ecologies [Proceedings of the 32nd Annual Conference of the Association for Computer Aided Design in Architecture (ACADIA) ISBN 978-1-62407-267-3] San Francisco 18-21 October, 2012), pp. 169-176
doi	https://doi.org/10.52842/conf.acadia.2012.169
summary	In this paper, viable applications of mobile robotic units on construction sites are explored. While expanding on potential objectives for in-situ fabrication in the construction sector, the intention is also to build upon innovative man-machine interaction paradigms to deal with the imprecision and tolerances often faced on construction sites. By combining the precision of the machine with the cognitive environmental human skills, a simple but effective mobile fabrication system is experimented for the building of algorithmically designed additive assemblies that would not be possible through conventional manual methods if the large amount of individual building blocks and the size of the structure to be built are taken into account. It is believed that this new approach to man-machine collaboration, aimed at a deeper integration of human ability with the strengths of digitally controlled machines, will result in advances in the construction sector, thus opening up new design and application fields for architects and planners.
keywords	in-situ robotic fabrication , mobile robotics , 1:1 scale fabrication , additive assembly , algorithmically designed structures , man-machine interaction , cognitive , object recognition , construction site
series	ACADIA
type	normal paper
email
last changed	2022/06/07 07:49

_id	acadia12_315
id	acadia12_315
authors	Imbern, Matias ; Raspall, Felix ; Su, Qi
year	2012
title	Tectonic Tessellations: A Digital Approach to Ceramic Structural Surfaces
source	ACADIA 12: Synthetic Digital Ecologies [Proceedings of the 32nd Annual Conference of the Association for Computer Aided Design in Architecture (ACADIA) ISBN 978-1-62407-267-3] San Francisco 18-21 October, 2012), pp. 315-321
doi	https://doi.org/10.52842/conf.acadia.2012.315
summary	From the beginning of digital revolution, structural surfaces drew significant attention as a realm that interweaves formal explorations, form-finding and structural optimization. However, after successful experimentation in the virtual domain, it became evident that some of the main challenges lay on how to translate these structural forms into architectural assemblies at the scale of buildings. The development of digital fabrication is crucial in this task, as means to overcome traditional constraints such as need for modular pieces, scaffolding and optimal assembly sequences.This research focuses on digital workflows that combine form finding with robotic fabrication, surface tessellation and panelization. In the past years, the use of digital tools to assemble identical modules into complex formations has achieved significant results for loadbearing walls. Expanding this line of research, the proposed fabrication system carries these experiments on additive fabrication into the production of structural surfaces. The assembly sequence involves a two-step fabrication: off-site panel manufacturing and on-site assembly. The main components of the system consist of two triangular ceramic pieces that provide structural resistance, refined surface finish, and formwork for thin reinforced-concrete layer. Panelization strategies reduce the requirements on-site work and formwork.The paper describes background research, concept, construction process, methodology, results and conclusions.
keywords	Digital Fabrication , Complex Geometry , Reinforced Ceramic , Structural Surfaces , Reduced Formwork
series	ACADIA
type	panel paper
email
last changed	2022/06/07 07:50

_id	acadia12_269
id	acadia12_269
authors	Lally, Sean
year	2012
title	Architecture of an Active Context
source	ACADIA 12: Synthetic Digital Ecologies [Proceedings of the 32nd Annual Conference of the Association for Computer Aided Design in Architecture (ACADIA) ISBN 978-1-62407-267-3] San Francisco 18-21 October, 2012), pp. 269-276
doi	https://doi.org/10.52842/conf.acadia.2012.269
summary	As we stand with our feet on earth’s outermost surface we build an architecture today that is much like it was several thousand years earlier, in an attempt to extend that outer shell with one of our own making. Artificial masses are built from a refinement of this existing geologic layer into materials of stone, steel, concrete, and glass that assemble to produce new pockets of space through the buildings they create. However, the sixth century BC writer Thales of Miletus put a different perspective on this: he insisted that we live, in reality, not on the summit of a solid earth but at the bottom of an ocean of air (Holmyard 1931). And so, as architecture continues to build up the outermost layer of earth’s surface through a mimicking, embellishing, and enhancing of the materials which it comes from, it raises the question of why we have not brought a similar relationship to the materialities at the bottom of this “ocean” of air to create the spaces we call architecture. If you were looking to level a complaint with the architectural profession, stating that it has not been ambitious enough in scope would not be one. Architects have never shied away from the opportunity to design everything from the building’s shell to the teaspoon used to stir your sugar in its matching cup. But it would seem that the profession has developed a rather large blind spot in terms of what it sees as a malleable material with which to engage. Architects have made assumptions as to what is beyond our scope of action, refraining from engaging a range of material variables due to a belief that the task would be too great or simply beyond our physical control. So even though we are enveloped by them continuously, both on the exterior as well as the interior of our buildings, it must be assumed that the particles, waves, and frequencies of energy that move around us are thought by architects to be too faint and shaky to unload upon them any heavy obligations, that they are too unwieldy for us to control to create the physical boundaries of separation, security, and movement required of architecture. This has resulted in a cultivated set of blinders that essentially defines architecture as a set of mediation devices (surfaces, walls, and inert masses) for tempering the environmental context it is situated in from the individuals and activities within. The spaces we inhabit are defined by their ability to decide what gets in and what stays out (sunlight, precipitation, winds). We place our organizational demands and aesthetic opinions on the surfaces that mediate these variables rather than seeing them as available for manipulation as a building material on their own. The intention here is to recalibrate the materialities that make up that environmental context to build architecture. The starting point is a rather naive question: can we design the energy systems that course in and around us daily as an architectural material so as to take on the needs of activities, securities, and lifestyles associated with architecture? Can the variables that we would normally mediate against instead be heightened and amplified so as to become the architecture itself? That which many would incorrectly dismiss as simply “air” today—thought to be homogeneous, scale-less, and vacant due in part to the limits of our human sensory system to perceive more fully otherwise—might tomorrow be further articulated, populated, and layered so as to become a materiality that will build spatial boundaries, define activities of individuals and movement, and act as architectural space. Our environmental context consists of a diverse range of materials (particles and waves of energy, spectrum of light, sound waves, and chemical particles) that can be manipulated and formed to meet our needs. The opportunity before us today is to embrace the needs of organizational structures and aesthetics by designing the active context that surrounds us through the material energies that define it.
keywords	Material energies
series	ACADIA
type	normal paper
email
last changed	2022/06/07 07:52

For more results click below: