Cumincad : CUMINCAD Papers : Search Results

CumInCAD is a Cumulative Index about publications in Computer Aided Architectural Design
supported by the sibling associations ACADIA, CAADRIA, eCAADe, SIGraDi, ASCAAD and CAAD futures

PDF papers
References

Hits 1 to 20 of 592

Reformat results as: short short into frame detailed detailed into frame

_id	ijac201311301
id	ijac201311301
authors	Hack, Norman; Willi Lauer, Silke Langenberg, Fabio Gramazio, Matthias Kohler
year	2013
title	Overcoming Repetition: Robotic fabrication processes at a large scale
source	International Journal of Architectural Computing vol. 11 - no. 3, 285-300
summary	In the context of the Future Cities Laboratory (FCL) of ETH Zurich, the Professorship for Architecture and Digital Fabrication of Fabio Gramazio and Matthias Kohler has set up a robotic laboratory to investigate the potentials of non-standard robotic fabrication for high rise constructions in Singapore. The high degree of industrialisation of this dominant building typology implies standardisation, simplification and repetition and accounts for the increasing monotony evident in many Asian metropolises. The aim of this research on material systems for robotic construction is to develop a new and competitive construction method that makes full use of the malleable potential of concrete as a building material. A novel, spatial, robotic "weaving" method of a tensile active material that simultaneously acts as the form defining mould, folds two separate aspects of concrete-reinforcement and formwork-into one single robotic fabrication process (see Figure 1). This in-situ process could permit the fabrication of structurally differentiated, spatially articulated and material efficient buildings.
series	journal
last changed	2019/05/24 09:55

_id	ijac201311302
id	ijac201311302
authors	Meagher, Mark; David van der Maas, Christian Abegg, Jeffrey Huang
year	2013
title	Dynamic ornament: An investigation of responsive thermochromic surfaces in architecture
source	International Journal of Architectural Computing vol. 11 - no. 3, 301-318
summary	This paper describes the use of environmental sensor data as a basis for the design of architectural ornament that takes on a distinctive appearance in response to the atmospheric conditions where it is located. Among the goals of the project were the identification of inexpensive fabrication methods that could be used to build responsive surfaces at the scale of a room, and the identification of material and tectonic strategies for integrating dynamic information displays in buildings. A series of prototypes were constructed to explore the benefits and limitations of thermochromic ink as a material for visualizing dynamic data, and a method is proposed for building thermochromic surfaces based on printed circuit boards (PCB's) that is cost-effective and allows the fabrication of large surfaces through tiling. The limitations of this method include high power consumption, a short lifespan and difficulties in controlling the surface temperature.
series	journal
last changed	2019/05/24 09:55

_id	caadria2013_033
id	caadria2013_033
authors	Nguyen, Danny D. and M. Hank Haeusler
year	2013
title	Assimilating Interactive Technology into Architectural Design – A Quest for developing an ‘Architectural Drawing’ for Urban Interaction Design as a Communication Platform Through Combining Physical Sensing Devices with Simulation Software
doi	https://doi.org/10.52842/conf.caadria.2013.365
source	Open Systems: Proceedings of the 18th International Conference on Computer-Aided Architectural Design Research in Asia (CAADRIA 2013) / Singapore 15-18 May 2013, pp. 365-373
wos	WOS:000351496100036
summary	Assimilating Interactive Technology into Architectural Design – A Quest for developing an ‘Architectural Drawing’ for Urban Interaction Design as a Communication Platform Through Combining Physical Sensing Devices with Simulation Software The research presented in this paper investigates the need for an equivalent of architectural drawings for urban interaction design in an architectural scale in order to communicate interaction design intentions to design participants and clients through using state of the art computer, gaming and sensor technologies. The paper discusses two projects (a) Blur Building, as a large scale interaction design project executed through an experienced team and (b) presents as student design project coordinated by the researchers as a reference project. Both projects in this paper are discussed and evaluated from an Urban Interaction Design point of view. This paper emphasizes the significance for establishing ‘drawing’ equivalents for urban interaction design, discussing representation of ideas in architectural design; followed by outlining existing methods of interactive design representation, such as storyboards to then introduce current advancements in gaming environments. The following paper introduces a framework for future research projects that will design, deploy and evaluate of prototypes as a communication platform combining physical sensing devices in combination with gaming engines to enable a digital / physical hybrid. This would allow designers and clients to test, evaluate and improve urban interactions in a design phase prior to completing the project.
keywords	Spatial design, Human-computing interfacing, Interactive architecture, Smart environments, Sensor technology
series	CAADRIA
email
last changed	2022/06/07 07:58

_id	acadia20_340
id	acadia20_340
authors	Soana, Valentina; Stedman, Harvey; Darekar, Durgesh; M. Pawar, Vijay; Stuart-Smith, Robert
year	2020
title	ELAbot
doi	https://doi.org/10.52842/conf.acadia.2020.1.340
source	ACADIA 2020: Distributed Proximities / Volume I: Technical Papers [Proceedings of the 40th Annual Conference of the Association of Computer Aided Design in Architecture (ACADIA) ISBN 978-0-578-95213-0]. Online and Global. 24-30 October 2020. edited by B. Slocum, V. Ago, S. Doyle, A. Marcus, M. Yablonina, and M. del Campo. 340-349.
summary	This paper presents the design, control system, and elastic behavior of ELAbot: a robotic bending active textile hybrid (BATH) structure that can self-form and transform. In BATH structures, equilibrium emerges from interaction between tensile (form active) and elastically bent (bending active) elements (Ahlquist and Menges 2013; Lienhard et al. 2012). The integration of a BATH structure with a robotic actuation system that controls global deformations enables the structure to self-deploy and achieve multiple three-dimensional states. Continuous elastic material actuation is embedded within an adaptive cyber-physical network, creating a novel robotic architectural system capable of behaving autonomously. State-of-the-art BATH research demonstrates their structural efficiency, aesthetic qualities, and potential for use in innovative architectural structures (Suzuki and Knippers 2018). Due to the lack of appropriate motor-control strategies that exert dynamic loading deformations safely over time, research in this field has focused predominantly on static structures. Given the complexity of controlling the material behavior of nonlinear kinetic elastic systems at an architectural scale, this research focuses on the development of a cyber-physical design framework where physical elastic behavior is integrated into a computational design process, allowing the control of large deformations. This enables the system to respond to conditions that could be difficult to predict in advance and to adapt to multiple circumstances. Within this framework, control values are computed through continuous negotiation between exteroceptive and interoceptive information, and user/designer interaction.
series	ACADIA
type	paper
email
last changed	2023/10/22 12:06

_id	caadria2013_021
id	caadria2013_021
authors	Alhadidi, Suleiman
year	2013
title	Generative Design Intervention: Creating a Computational Platform for Sensing Space
doi	https://doi.org/10.52842/conf.caadria.2013.345
source	Open Systems: Proceedings of the 18th International Conference on Computer-Aided Architectural Design Research in Asia (CAADRIA 2013) / Singapore 15-18 May 2013, pp. 345-354
wos	WOS:000351496100034
summary	This paper outlines some investigations from a project which utilizes computing and scripting of specific site components, spatio-temporal movement and behavioural patterns to explore how designer might understand people activities and formulate design interventions within public spaces. This research looks at how generative tools can facilitate designers to integrate the large volume of information received by hybrid data collection, and conventional data analysis directly into the design process. Through an examination of sensing urban space, this research proposes a method to track and record people’s movement patterns in order to implement them via generative design tool. To facilitate this, a scripting method is specified; which uses sensors and motion tracking devices to capture the use of a specific public space. This project proposes a methodology for developing designed spaces and optimal pathways generated from real-time data and feedback captured by sensors.
keywords	Real-time computation, Generative design, Sensing space, Design simulation
series	CAADRIA
email
last changed	2022/06/07 07:54

_id	lasg_nearlivingarchitecture_2014_045
id	lasg_nearlivingarchitecture_2014_045
authors	Armstrong, Rachel
year	2014
title	Potent Matter; The Dynamic Chemistries of Hylozoic Ground
source	Near-Living Architecture; Work in Progress from The Hylozoic Ground Collaboration 2011 - 2013 [ISBN 978-1-926724-45-4 (pbk).--ISBN 978-1-926724-57-7 (epub).--ISBN 978-1-926724-58-4 (mobi)] Riverside Architectural Press: Toronto, Canada 2014 pp. 045 - 062
keywords	Living Architecture Systems Group, living architecture, meshworks, metabolisms, kinetic, cybernetic, artificial intelligence, cognition, neuroscience, prototyping, diffusive, subtle phenomena, form-languge, chemistry, natural computing, affect, perception
email
last changed	2019/07/29 14:00

_id	ecaade2018_243
id	ecaade2018_243
authors	Gardner, Nicole
year	2018
title	Architecture-Human-Machine (re)configurations - Examining computational design in practice
doi	https://doi.org/10.52842/conf.ecaade.2018.2.139
source	Kepczynska-Walczak, A, Bialkowski, S (eds.), Computing for a better tomorrow - Proceedings of the 36th eCAADe Conference - Volume 2, Lodz University of Technology, Lodz, Poland, 19-21 September 2018, pp. 139-148
summary	This paper outlines a research project that explores the participation in, and perception of, advanced technologies in architectural professional practice through a sociotechnical lens and presents empirical research findings from an online survey distributed to employees in five large-scale architectural practices in Sydney, Australia. This argues that while the computational design paradigm might be well accepted, understood, and documented in academic research contexts, the extent and ways that computational design thinking and methods are put-into-practice has to date been less explored. In engineering and construction, technology adoption studies since the mid 1990s have measured information technology (IT) use (Howard et al. 1998; Samuelson and Björk 2013). In architecture, research has also focused on quantifying IT use (Cichocka 2017), as well as the examination of specific practices such as building information modelling (BIM) (Cardoso Llach 2017; Herr and Fischer 2017; Son et al. 2015). With the notable exceptions of Daniel Cardoso Llach (2015; 2017) and Yanni Loukissas (2012), few scholars have explored advanced technologies in architectural practice from a sociotechnical perspective. This paper argues that a sociotechnical lens can net valuable insights into advanced technology engagement to inform pedagogical approaches in architectural education as well as strategies for continuing professional development.
keywords	Computational design; Sociotechnical system; Technology adoption
series	eCAADe
email
last changed	2022/06/07 07:51

_id	ijac201310102
id	ijac201310102
authors	Kocaturk, Tuba
year	2013
title	Emerging Socio-Technical Networks of Innovation in Architectural Practice
source	International Journal of Architectural Computing vol. 11 - no. 1, 21-36
summary	This article reports on the initial analyses and findings of on-going research project which investigates the socio-technical transformation of Architectural practice due to technology adoption.A conceptual framework is developed as a tool to identify, analyse, and characterize the different socio-technical networks in current practice, and the ways in which these networks are being developed and coordinated. Highly technology- mediated and interdisciplinary architectural/engineering practices have been monitored and studied in their real-life project contexts.Through comparative case analyses, a conceptual framework has been developed and used to represent and analyse emerging socio- technical networks and the ways in which these networks facilitate innovation. In this context, new modes/practices of innovations are identified through the diverse and dynamic relationships emerging between architects, digital tools/systems, the design artefact, and the various multi-disciplinary knowledge/actors in a socio-technical setting.
series	journal
last changed	2019/05/24 09:55

_id	acadia13_061
id	acadia13_061
authors	Bruscia, Nicholas; Romano, Christopher
year	2013
title	Material Parameters and Digitally Informed Fabrication of Textured Metals
doi	https://doi.org/10.52842/conf.acadia.2013.061
source	ACADIA 13: Adaptive Architecture [Proceedings of the 33rd Annual Conference of the Association for Computer Aided Design in Architecture (ACADIA) ISBN 978-1-926724-22-5] Cambridge 24-26 October, 2013), pp. 61-68
summary	The research represented in this paper proposes to reinvestigate the relationship between structure and appearance through a performative analysis of textured stainless steel, as verified through full-scale prototyping. The work takes a scientific design approach while incorporating a computational workflow that is informed by the material’s physical parameters, and draws a connection between the scales of molecular composition to large-scale geometric systems.Furthermore, the work attempts to provide evidence for thin-gauge textured metals as a high performance and adaptive material, by identifying structural rigidity and particular specular quality as inherent characteristics born from the texturing process. In addition, through close collaboration with the sponsoring manufacturer of textured stainless steel, we are able to gain access to material expertise and large-scale fabrication equipment not readily available to designers, thereby forging a mutually beneficial relationship surrounding the research.
keywords	Next Generation Technology, Architecture and Manufacturing, Material Research, Material Science, Digital Fabrication, Rigidized Metal, Parametric Modeling
series	ACADIA
type	Normal Paper
email
last changed	2022/06/07 07:54

_id	acadia13_301
id	acadia13_301
authors	Dierichs, Karola; Menges, Achim
year	2013
title	Aggregate Architecture: Simulation Models for Synthetic Non-convex Granulates
doi	https://doi.org/10.52842/conf.acadia.2013.301
source	ACADIA 13: Adaptive Architecture [Proceedings of the 33rd Annual Conference of the Association for Computer Aided Design in Architecture (ACADIA) ISBN 978-1-926724-22-5] Cambridge 24-26 October, 2013), pp. 301-310
summary	Aggregate Architectures challenge the common notion of architectural structures as being immutable, permanent and controllable. Aggregate Architectures are understood as material systems consisting of large masses of granules—designed or natural—interacting with each other only through loose, frictional contact. As a consequence, they take the realm of structural stability and architectural planning into entire re-configurability and into merely probable predictions of their prospective behavior. This renders them relevant within the paradigm of Adaptive Architecture.The challenge to the designer is to move away from thinking in terms of clearly defined local and global assembly systems and to acquire tools and modes of design that allow for observation and interaction with the evolving granular architectures. In this context, the focus of the presented researchproject is on the relevance of mathematically based simulations as tools of investigation and design.The paper introduces the field of Aggregate Architectures. Consequently experimental and simulation methods for granulates will be outlined and compared. Different modeling and collision-detection methods for non-convex particles are shown and applied in benchmarking simulations for a full-scale architectural prototype. The potential for micro-mechanical simulation analysis within architectural applications are demonstrated and further areas of research outlined.
keywords	Tools and Interfaces; aggregate architecture, designed granular matter, discrete element modeling, non-convex particles
series	ACADIA
type	Normal Paper
email
last changed	2022/06/07 07:55

_id	ecaade2013_184
id	ecaade2013_184
authors	Fraguada, Luis; Girot, Christophe and Melsom, James
year	2013
title	Ambient Terrain
doi	https://doi.org/10.52842/conf.ecaade.2013.1.433
source	Stouffs, Rudi and Sariyildiz, Sevil (eds.), Computation and Performance – Proceedings of the 31st eCAADe Conference – Volume 1, Faculty of Architecture, Delft University of Technology, Delft, The Netherlands, 18-20 September 2013, pp. 433-438
wos	WOS:000340635300045
summary	‘Ambient Terrain’ explores the application of large-scale, sensor-based site analysis. The research develops various techniques dealing with the logging, storage, retrieval, analysis, and representation of sensor and image-based data. These techniques could be utilized in concert with traditional site preparation and site information gathering processes, and could arguably serve to reevaluate the site preparation process altogether in a manner which not only focuses on terrestrial data, but also on metrics which are dynamic and multidimensional.The research proposes direct applications for urban space and the built environment, in the modes of site appraisal, design and the generation of new spatial strategies.
keywords	Unmanned Aerial Vehicle; sensor data logging, ambient site analysis, UAV data collection; photogrammetry, stereophotogrammetry.
series	eCAADe
email
last changed	2022/06/07 07:50

_id	caadria2013_071
id	caadria2013_071
authors	Lloret Kristensen, Ena; Fabio Gramazio, Matthias Kohler and Silke Langenberg
year	2013
title	Complex Concrete Constructions – Merging Existing Casting Techniques with Digital Fabrication
doi	https://doi.org/10.52842/conf.caadria.2013.613
source	Open Systems: Proceedings of the 18th International Conference on Computer-Aided Architectural Design Research in Asia (CAADRIA 2013) / Singapore 15-18 May 2013, pp. 613-622
wos	WOS:000351496100060
summary	In the course of the 20th century, architectural construction has gone through intense innovation in its material, engineering and design, radically transforming the way buildings were and are conceived. Technological and industrial advances enabled and challenged architects, engineers and constructors to build increasingly complex architectural structures from concrete. Computer-Aided Design and Manufacturing (CAD/CAM) techniques have, more recently, rejuvenated and increased the possibilities of realising ever more complex geometries. Reinforced concrete is often chosen for such structures since almost any shape can be achieve when poured into a formwork. However, designs generated with digital tools tend to have limited relation to the efficient modes of production typically used in contemporary concrete construction. A large gap has emerged between the technology in architectural design and the building industry, so that few efficient solutions exist for the production of geometrically complex structures in concrete. This paper focuses on the capabilities and efficiency of existing casting techniques both with static and dynamic formwork which, when combined with digital fabrication, allow innovative fabrication approaches to be taken. Particular focus is placed on slipforming, an approved and efficient construction technique, which until now is unexplored in conjunction with digital fabrication.
keywords	Complex concrete structures, Casting techniques, Formwork, Slipforming, Digital fabrication, Smart dynamic casting
series	CAADRIA
email
last changed	2022/06/07 07:59

_id	caadria2016_497
id	caadria2016_497
authors	Ryu, Jungrim; Jaehong Jun, Seunghyeon Lee and Seungyeon Choo
year	2016
title	A Study on Development of the IFC-based Indoor Spatial Information for Data Visualisation
doi	https://doi.org/10.52842/conf.caadria.2016.497
source	Living Systems and Micro-Utopias: Towards Continuous Designing, Proceedings of the 21st International Conference on Computer-Aided Architectural Design Research in Asia (CAADRIA 2016) / Melbourne 30 March–2 April 2016, pp. 497-506
summary	MOLIT authorised Indoor Spatial Information as Basic spa- tial information in 2013. It became a legal evidence for constructing and managing Indoor Spatial Information. Although it has a little ad- vantage to utilise as service level that Indoor Spatial Information by laser scan or measurement, it has a lot of problems such as consuming many resources, requiring additional progresses for inputting Object Information. In conclusion, it is inefficient to utilise for the mainte- nance and domestic AEC/FM field. The purposes of this study is to output Indoor Spatial Information by operating IFC model which based on open BIM and to improve availability of Indoor Spatial In- formation with data visualisation. The open-sources of IFC Exporter, an inner program of Revit, is used to output Indoor Spatial Infor- mation. Directs 3D Library is also operated to visualise Indoor Spatial Information. It is possible to inter-operate between XML format and the objects of Indoor Spatial Information. It can be utilised in various field as well. For example COBie linkage in facility management, construction of geo-database using air-photogrammetry of UA V , the simulation of large-scale military operations and the simulation of large-scale evacuation. The method that is purposed in this study has outstanding advantages such as conformance with national spatial in- formation policy, high level of interoperability as indoor spatial in- formation objects based on IFC, convenience of editing information, light level of data and simplifying progress of producing information.
keywords	Indoor spatial information, data visualisation, open BIM, IFC
series	CAADRIA
email
last changed	2022/06/07 07:56

_id	acadia13_347
id	acadia13_347
authors	Sabin, Jenny E.
year	2013
title	myThread Pavilion: Generative Fabrication in Knitting Processes
doi	https://doi.org/10.52842/conf.acadia.2013.347
source	ACADIA 13: Adaptive Architecture [Proceedings of the 33rd Annual Conference of the Association for Computer Aided Design in Architecture (ACADIA) ISBN 978-1-926724-22-5] Cambridge 24-26 October, 2013), pp. 347-354
summary	Advancements in weaving, knitting and braiding technologies have brought to surface high-tech and high- performance composite fabrics. These products have historically infiltrated the aerospace, automobile, sports and marine industries, but architecture has not yet fully benefitted from these lightweight freeform surface structures. myThread, a commission from the Nike FlyKnit Collective, features knitted textile structures at the scale of a pavilion. The evolution of digital tools in architecture has prompted new techniques of fabrication alongside new understandings in the organization of material through its properties and potential for assemblage. No longer privileging column, beam and arch, our definition of architectural tectonics has broadened alongside advancements made in computational design. Internal geometries inherent to natural forms, whose complexity could not be computed with the human mind alone, may now be explored synthetically through mathematics and generative systems. Textiles offer architecture a robust design process whereby computational techniques, pattern manipulation, material production and fabrication are explored as an interconnected loop that may feed back upon itself in no particular linear fashion. The myThread Pavilion integrates emerging technologies in design through the materialization of dynamic data sets generated by the human body engaged in sport and movement activities in the city.
keywords	next generation technology, textiles, responsive material, knitting, data visualization, generative design, bio-data
series	ACADIA
type	Normal Paper
email
last changed	2022/06/07 07:59

_id	caadria2013_223
id	caadria2013_223
authors	Schimek, Heimo; Albert Wiltsche, Markus Manahl and Christoph Pfaller
year	2013
title	Full Scale Prototyping – Logistic and Construction Challenges Realising Digitally Designed Timber Prototypes
doi	https://doi.org/10.52842/conf.caadria.2013.653
source	Open Systems: Proceedings of the 18th International Conference on Computer-Aided Architectural Design Research in Asia (CAADRIA 2013) / Singapore 15-18 May 2013, pp. 653-662
wos	WOS:000351496100064
summary	This paper reports on the final stage of a research project with the realization of a real scale prototype and ties an empirical finale to the project, which started as a fundamental research project three years ago. The scope of this research project was to explore new ways, how Non-Standard Architecture can be build with standard building elements using contemporary building processes and materials resource efficiently. Mass Customization and File to Factory, concepts where a continuous digital workflow is applied, were fundamental to our approach. Within this framework we developed generic parametric details and made them part of the whole process from the beginning of the design to the manufacturing. The present paper describes a strategy for the assembly of a large prototype, consisting of approximately 50 flat timber panels that are being assembled to a structure of the size of a small house. The paper focuses especially on the customized falsework, we designed for the construction of the prototype, which became a crucial part of the assembling process besides the assembly of the actual prototype.
keywords	Digital fabrication and construction, Precedence and prototypes, Mass customization
series	CAADRIA
email
last changed	2022/06/07 07:57

_id	caadria2013_030
id	caadria2013_030
authors	Adamantidis, Ermis; Madhav Kidao and Marios Tsiliakos
year	2013
title	Siphonophore – A Physical Computing Simulation of Colonial Intelligence Organisms
doi	https://doi.org/10.52842/conf.caadria.2013.355
source	Open Systems: Proceedings of the 18th International Conference on Computer-Aided Architectural Design Research in Asia (CAADRIA 2013) / Singapore 15-18 May 2013, pp. 355-364
wos	WOS:000351496100035
summary	This paper sets out to document the procedural design and implementation of “Siphonophore” a multisensory digital ecology, mimicking colonial-ordered behaviour systems. The exploration of the notion of “self” in a complex system of highly integrated individuals with reference to the emergence of behaviours from the human-machine-context interaction, is engaged by this open system’s hierarchical articulation of electronics, Arduino boards, sensors and programming routines. User interaction and recorded statistics from the system’s core algorithm are assessed, in relation to the capacity of this prototype to provide an alternative methodology of describing collective intelligence, while presenting a non-standard perspective of body-space interaction and design as entertaining art. The overall impact is discussed in relation to the examined observations, towards a potential advancement to a system of superior contextual understanding.
keywords	Colonial intelligence, Multisensory installation, Physical computing, Spatial sensing, Human-machine interaction
series	CAADRIA
email
last changed	2022/06/07 07:54

_id	caadria2013_210
id	caadria2013_210
authors	Baerlecken, Daniel; Katherine Johnson and Alice Vialard
year	2013
title	Mobilized Materials – Textile Constructs
doi	https://doi.org/10.52842/conf.caadria.2013.333
source	Open Systems: Proceedings of the 18th International Conference on Computer-Aided Architectural Design Research in Asia (CAADRIA 2013) / Singapore 15-18 May 2013, pp. 333-342
wos	WOS:000351496100033
summary	This paper investigates textiles techniques and their potential for creating ornamental and structural systems investigated through a sequence of design studios. Within the paper 3 examples of textile systems are introduced that range from a Semperian approach (wall as dress) to form finding experiments with active textile materials (Frei Otto).
keywords	extiles, Form-finding, Analogue computing, Design methodology, Craft
series	CAADRIA
email
last changed	2022/06/07 07:54

_id	lasg_nearlivingarchitecture_2014_fulltext
id	lasg_nearlivingarchitecture_2014_fulltext
authors	Beesley, Philip [editor]
year	2014
title	Euphoria and Dystopia
source	Near-Living Architecture; Work in Progress from The Hylozoic Ground Collaboration 2011 - 2013 [ISBN 978-1-926724-45-4 (pbk).--ISBN 978-1-926724-57-7 (epub).--ISBN 978-1-926724-58-4 (mobi)] Riverside Architectural Press: Toronto, Canada 2014
keywords	Living Architecture Systems Group, living architecture, meshworks, metabolisms, kinetic, cybernetic, artificial intelligence, cognition, neuroscience, prototyping, diffusive, subtle phenomena, form-languge, chemistry, natural computing, affect, perception
email
last changed	2019/07/29 14:00

_id	lasg_nearlivingarchitecture_2014_008
id	lasg_nearlivingarchitecture_2014_008
authors	Beesley, Philip
year	2014
title	Introduction
source	Near-Living Architecture; Work in Progress from The Hylozoic Ground Collaboration 2011 - 2013 [ISBN 978-1-926724-45-4 (pbk).--ISBN 978-1-926724-57-7 (epub).--ISBN 978-1-926724-58-4 (mobi)] Riverside Architectural Press: Toronto, Canada 2014 pp. 008 - 034
keywords	Living Architecture Systems Group, living architecture, meshworks, metabolisms, kinetic, cybernetic, artificial intelligence, cognition, neuroscience, prototyping, diffusive, subtle phenomena, form-languge, chemistry, natural computing, affect, perception
email
last changed	2019/07/29 14:00

_id	lasg_nearlivingarchitecture_2014_035
id	lasg_nearlivingarchitecture_2014_035
authors	Beesley, Philip
year	2014
title	Diffusive Prototyping
source	Near-Living Architecture; Work in Progress from The Hylozoic Ground Collaboration 2011 - 2013 [ISBN 978-1-926724-45-4 (pbk).--ISBN 978-1-926724-57-7 (epub).--ISBN 978-1-926724-58-4 (mobi)] Riverside Architectural Press: Toronto, Canada 2014 pp. 035 - 044
keywords	Living Architecture Systems Group, living architecture, meshworks, metabolisms, kinetic, cybernetic, artificial intelligence, cognition, neuroscience, prototyping, diffusive, subtle phenomena, form-languge, chemistry, natural computing, affect, perception
email
last changed	2019/07/29 14:00

For more results click below: