Cumincad : CUMINCAD Papers : Search Results

CumInCAD is a Cumulative Index about publications in Computer Aided Architectural Design
supported by the sibling associations ACADIA, CAADRIA, eCAADe, SIGraDi, ASCAAD and CAAD futures

PDF papers
References

Hits 1 to 20 of 567

Reformat results as: short short into frame detailed detailed into frame

_id	acadia15_371
id	acadia15_371
authors	Hatefnia, Navid; Ghobad, Marjan
year	2015
title	Computing Outdoor Comfort Based on CBE Thermal Comfort Calculation for Ashrae-55
doi	https://doi.org/10.52842/conf.acadia.2015.371
source	ACADIA 2105: Computational Ecologies: Design in the Anthropocene [Proceedings of the 35th Annual Conference of the Association for Computer Aided Design in Architecture (ACADIA) ISBN 978-0-692-53726-8] Cincinnati 19-25 October, 2015), pp. 371-480
summary	Environmental analysis as part of the initial design process, affords precise consideration of the bioclimatic human conditions within the environmental local context. The daily growth in inter alia knowledge of effective parameters in environmental conditions, quality weather data, human thermo-physiology studies – all contribute to improving the potential for achieving a relatively accurate analyses of environmental conditions by overlaying and computing all the climatic and thermo-physiological data. This paper describes a digital method for examining different points in the same context by computing all the input data available to understand the corresponding human comfort condition levels, thus leading to better decision-making at early design stages. Information about the site, climate, human thermo-physiology and behavioral aspects among others are collected where each data parameter is matched and analyzed to the context of every node on the model through a series of specific computational algorithms. Thereafter, the data from the nodes are statistically cleaned, classified and integrated based on the CBE thermal comfort calculation for ASHRAE-55. The results obtained using this method, can be tailored according to the desired outcomes. The proposed method identifies effective factors for human comfort condition improvement for different points on the context. It also provides a means to priorities specific parameters so that they can be manipulated for optimal digital design solutions, ie. Aligned to the desired conditions in the specific parts of the site with the aim of optimize outdoor space usage.
keywords	Micro-Climate, Outdoor Comfort, Urban Design, Environmental Aspects, Bio-Climatic Conditions
series	ACADIA
type	normal paper
email
last changed	2022/06/07 07:49

_id	ecaade2015_116
id	ecaade2015_116
authors	Bieg, Kory
year	2015
title	SUPRAFICIAL: Building (an) Information Network
doi	https://doi.org/10.52842/conf.ecaade.2015.1.277
source	Martens, B, Wurzer, G, Grasl T, Lorenz, WE and Schaffranek, R (eds.), Real Time - Proceedings of the 33rd eCAADe Conference - Volume 1, Vienna University of Technology, Vienna, Austria, 16-18 September 2015, pp. 277-284
summary	This paper explores the potential of using multiple software programs to generate an adaptable, cross-platform Building Information Network to unlock new territories of form-making and design. By using multiple software packages to overcome the limitations imposed by current BIM (Building Information Model) programs and mono-scalar design approaches, we can design a buildings form, envelope, and materiality through an adaptable, parametric design process that uses the best features of each software program, allows non-computational input to inform form, and takes advantage of a designer's unique self-expression.
wos	WOS:000372317300030
series	eCAADe
email
more	https://mh-engage.ltcc.tuwien.ac.at/engage/ui/watch.html?id=40efae5a-702e-11e5-83aa-771f3575946f
last changed	2022/06/07 07:52

_id	cf2015_331
id	cf2015_331
authors	Brodeschi, Michal; Pilosof, Nirit Putievsky and Kalay, Yehuda E.
year	2015
title	The definition of semantic of spaces in virtual built environments oriented to BIM implementation
source	The next city - New technologies and the future of the built environment [16th International Conference CAAD Futures 2015. Sao Paulo, July 8-10, 2015. Electronic Proceedings/ ISBN 978-85-85783-53-2] Sao Paulo, Brazil, July 8-10, 2015, pp. 331-346.
summary	The BIM today can be a provider of inputs to performance analysis of different phenomena such as thermal comfort, energy consumption or winds. All these assessments are fundamental to the post occupation of the building. The attainment of approximate information of how the future building would behave under these conditions will reduce the waste of materials and energy resources. The same idea is used for evaluating the users occupation. Through simulation of human behavior is possible to evaluate which design elements can be improved. In complex structures such as hospital buildings or airports is quite complex for architects to determine optimal design solutions based on the tools available nowadays. These due to the fact users are not contemplated in the model. Part of the data used for the simulation can be derived from the BIM model. The three-dimensional model provides parametric information, however are not semantically enriched. They provide parameters to elements but not the connection between them, not the relationship. It means that during a simulation Virtual Users can recognize the elements represented in BIM models, but not what they mean, due to the lack of semantics. At the same time the built environment may assume different functions depending on the physical configuration or activities that are performed on it. The status of the space may reveal differences and these changes occur constantly and are dynamic. In an initial state, a room can be noisy and a moment later, quiet. This can determine what type of activities the space can support according to each change in status. In this study we demonstrate how the spaces can express different semantic information according to the activity performed on it. The aim of this paper is to simulate the activities carried out in the building and how they can generate different semantics to spaces according to the use given to it. Then we analyze the conditions to the implementation of this knowledge in the BIM model.
keywords	BIM, Virtual Sensitive Environments, Building Use Simulation, Semantics.
series	CAAD Futures
email
last changed	2015/06/29 07:55

_id	ecaade2015_169
id	ecaade2015_169
authors	Nakama, Yuki; Onishi, Yasunobu and Iki, Kazuhisa
year	2015
title	Development of Building Information Management System with Data Collecting Functions based on IoT Technology
doi	https://doi.org/10.52842/conf.ecaade.2015.1.647
source	Martens, B, Wurzer, G, Grasl T, Lorenz, WE and Schaffranek, R (eds.), Real Time - Proceedings of the 33rd eCAADe Conference - Volume 1, Vienna University of Technology, Vienna, Austria, 16-18 September 2015, pp. 647-655
summary	Facility management is aimed at energy saving, increasing the lifespan of buildings, enhancing the satisfaction of facility users and reducing running costs. To that end, it is important to grasp the conditions of the building in detail, and to analyze them one by one in order to execute building operation and maintenance strategically. However, conventional CAFM is insufficient. Therefore, we developed a system (called Building Information Management System) to utilize BIM data made on a Web site. We used groupware to support the system and an information platform that enables continuous management of a great variety of maintenance information. In addition, we developed a system to input information of building operation and maintenance using a mobile device on the site of checking and patrolling so as to reduce the burden of inputting information. A sensor network is used to acquire building operation and maintenance information to enhance building operation and maintenance. We also developed a system to automatically input sensing information into the building information for Building Information Management System, and to connect it with a 3D model. It has therefore become easier to collect the large amount of information necessary for strategic building operation and maintenance.
wos	WOS:000372317300070
series	eCAADe
email
more	https://mh-engage.ltcc.tuwien.ac.at/engage/ui/watch.html?id=0d63b958-7021-11e5-a1ec-00190f04dc4c
last changed	2022/06/07 07:59

_id	sigradi2015_sp_8.284
id	sigradi2015_sp_8.284
authors	Queiroz, Natália; Dantas, Ney; Nome, Carlos; Vaz, Carlos
year	2015
title	Designing a Building envelope using parametric and algorithmic processes
source	SIGRADI 2015 [Proceedings of the 19th Conference of the Iberoamerican Society of Digital Graphics - vol. 2 - ISBN: 978-85-8039-133-6] Florianópolis, SC, Brasil 23-27 November 2015, pp. 797-801.
summary	This article presents a case study on a vertical building envelope design considering Recife ?s climatic conditions. It consists of the utilization of parametric and algorithmic processes to distribute sun shading devices. The study uses computational tools such as Grasshopper and the DIVA for Grasshopper. The latter is a thermal energy simulation tool that uses the Energy Plus 7.0 and Daysim for calculations. The model uses incident solar radiation simulation on the envelope as basis for distribution of shading devices. The result is a parametric model that automatically responds to urban and climatic characteristics, through simulations integrated to the 3D model.
keywords	Shading Devices, Parameterization, Grasshopper, DIVA
series	SIGRADI
email
last changed	2016/03/10 09:58

_id	cf2015_485
id	cf2015_485
authors	Anaf, Márcia and Harris, Ana Lúcia Nogueira de Camargo
year	2015
title	The geometry of Chuck Hoberman as the basis for the development of dynamic experimental structures
source	The next city - New technologies and the future of the built environment [16th International Conference CAAD Futures 2015. Sao Paulo, July 8-10, 2015. Electronic Proceedings/ ISBN 978-85-85783-53-2] Sao Paulo, Brazil, July 8-10, 2015, pp. 485.
summary	The cognitive-theoretical foundation referring to teach drawing as a way of thinking, as well as the construction of the environment by means of drawing using transforming geometries and the formal and para-formal computational process, creating unusual geometries through generative design processes and methodologies, can be seen as some of the main possibilities in exploring dynamic experimental structures for an Adaptive Architecture. This article presents the development of a model for articulated facades, inspired by Hoberman´s Tessellates, and his Adaptive Building Initiative (ABI) project to develop facades models that respond in real time to environmental changes. In addition, we describe an experiment based on the retractable structures, inspired by Hoberman´s work and experimentations. Solutions for responsive facades can offer more flexible architectural solutions providing better use of natural light and contributing to saving energy. Using Rhinoceros and the Grasshopper for modeling and test the responsiveness, the parametric model was created to simulate geometric panels of hexagonal grids that would open and close in reaction to translational motion effects, regulating the amount of light that reaches the building.
keywords	Parametric architecture, Hoberman´s Tessellates, Adaptive Building Initiative (ABI), Articulated Facades, Complex Geometries, Retractable structures, Retractable polyhedra.
series	CAAD Futures
email
last changed	2015/06/29 07:55

_id	cf2015_304
id	cf2015_304
authors	Barrios, Carlos and Mostafa, Alani
year	2015
title	Parametric Analysis in Islamic Geometric Designs
source	The next city - New technologies and the future of the built environment [16th International Conference CAAD Futures 2015. Sao Paulo, July 8-10, 2015. Electronic Proceedings/ ISBN 978-85-85783-53-2] Sao Paulo, Brazil, July 8-10, 2015, pp. 304-322.
summary	A method for the analysis of metamorphosis in traditional Islamic geometrical patterns using a parametric model is presented. The method uses traditional Islamic geometry as a starting point and performs an analysis of pattern’s fundamental units and cells and presents metamorphosis operation based on parametric variations of geometry and color.
keywords	Islamic Geometric Patterns, Pattern Generation, Parametric Modeling, Color, Parametric Variations, Metamorphosis.
series	CAAD Futures
email
last changed	2015/06/29 07:55

_id	cf2015_268
id	cf2015_268
authors	Benedetto, Henrique; Kipper, Fabrício A.;Marques, Vinícius and Bruscato, Underléa M.
year	2015
title	Development of Parklets by using parametric modeling
source	The next city - New technologies and the future of the built environment [16th International Conference CAAD Futures 2015. Sao Paulo, July 8-10, 2015. Electronic Proceedings/ ISBN 978-85-85783-53-2] Sao Paulo, Brazil, July 8-10, 2015, pp. 268-278.
summary	The lack of urban planning has made the recreation areas increasingly smaller in the cities. Parks and squares gradually gave way to streets and avenues to try to accommodate the growing number of cars and motorcycles. An alternative that tries to balance recreation areas and urban roads was found in the city of San Francisco (USA). Parklets are temporary extensions of urban sidewalks that occupy a few parking spaces. This article aims to demonstrate the potential of parametric modeling in the development of parklets. Thus, anthropometric studies, amount of parking spaces and types of benches were used as input parameters. Rhinoceros and grasshopper programs were used for modeling, while 3D Studio Max was used for rendering. With this study it was possible to verify that when the project is parameterized the processes of creation and modification became faster, reducing design and implementation time.
keywords	Grasshopper algorithm editor, Parametric model, Parklets.
series	CAAD Futures
email
last changed	2015/06/29 07:55

_id	sigradi2015_3.9
id	sigradi2015_3.9
authors	Bola?os-Mora, Adriana; Colpes, Karen Mello; Filho, Aderson. A. Passos; Bruscato, Underléa; Silva, Tânia Luisa Koltermann da; Silva, Régio Pierre da
year	2015
title	Parametric Modeling applied to an Assistive Technology Product Design
source	SIGRADI 2015 [Proceedings of the 19th Conference of the Iberoamerican Society of Digital Graphics - vol. 1 - ISBN: 978-85-8039-135-0] Florianópolis, SC, Brasil 23-27 November 2015, pp. 60-64.
summary	The article presents an Assistive Technology product design, which aims to overcome the medical product idea, considering its aesthetic configuration, and aims to change the concept of mass production into custom manufacturing. The methodological process was to obtain the user’s body 3D model, for subsequent parameterization by using the Grasshopper’s Rhinoceros Plugin software. It is believed that the digital manufacturing process provides a more flexible production, especially in the prototyping and testing stages, which seems a competitive advantage over companies that do not use them.
series	SIGRADI
email
last changed	2016/03/10 09:47

_id	cf2015_326
id	cf2015_326
authors	Borges, Marina and Fakury, Ricardo H.
year	2015
title	Structural design based on performance applied to development of a lattice wind tower
source	The next city - New technologies and the future of the built environment [16th International Conference CAAD Futures 2015. Sao Paulo, July 8-10, 2015. Electronic Proceedings/ ISBN 978-85-85783-53-2] Sao Paulo, Brazil, July 8-10, 2015, pp. 326.
summary	This paper studies the process of parametric and algorithmic design, integrating structural analysis and design for the generation of complex geometric structures. This methodology is based on the Performative Model, where the shape is generated using performance criteria. In the approach, the development of complex structures is only possible by reversing the process of thinking to generate the form with established parameters for geometry, material and loading aspects. Thus, the structural engineer no longer only participates in the evaluation phase but also appears in the early stages, creating a process of exploration and production of common knowledge among architects and engineers. To research performance-based design, the development of a conceptual lattice for a wind tower is proposed. Thus, a system is made to generate geometries using Rhinoceros software, the Grasshopper plugin, and the VB programming language, integrated with stress analysis through the Scan & Solve plugin.
keywords	Structural Design, Parametric and Algorithm Architecture, Structural Analysis, Performative Model, Lattice Wind Tower.
series	CAAD Futures
email
last changed	2015/06/29 07:55

_id	eaea2015_t3_paper04
id	eaea2015_t3_paper04
authors	Breen, Jack
year	2015
title	Thematic Visualisation Studies: The AA Variations
source	ENVISIONING ARCHITECTURE: IMAGE, PERCEPTION AND COMMUNICATION OF HERITAGE [ISBN 978-83-7283-681-6],Lodz University of Technology, 23-26 September 2015, pp.309-318
summary	The underlying thesis of the research described in this paper is that imaginative, model-based explorations may help us better understand iconic architectural artefacts, such as cultural heritage projects. In order to systematically consider and study architectural artefacts, it is essential for academics to reach a level of clarity – and potentially even consensus – concerning the domains of architectural design that may be considered relevant and to question - often implicitly – shared conceptions. This paper intends to communicate the results and findings of an in-depth case-based exploration on the basis of ten design artefacts, using a specially developed conceptual framework. Furthermore, the aim was to draw conclusions concerning the benefits and potentials of this approach in the context of heritage-based architectural research in an academic environment.
keywords	iconic architecture; 3D modelling; design education
series	EAEA
email
last changed	2016/04/22 11:52

_id	acadia17_202
id	acadia17_202
authors	Cupkova, Dana; Promoppatum, Patcharapit
year	2017
title	Modulating Thermal Mass Behavior Through Surface Figuration
doi	https://doi.org/10.52842/conf.acadia.2017.202
source	ACADIA 2017: DISCIPLINES & DISRUPTION [Proceedings of the 37th Annual Conference of the Association for Computer Aided Design in Architecture (ACADIA) ISBN 978-0-692-96506-1] Cambridge, MA 2-4 November, 2017), pp. 202-211
summary	This research builds upon a previous body of work focused on the relationship between surface geometry and heat transfer coefficients in thermal mass passive systems. It argues for the design of passive systems with higher fidelity to multivariable space between performance and perception. Rooted in the combination of form and matter, the intention is to instrumentalize design principles for the choreography of thermal gradients between buildings and their environment from experiential, spatial and topological perspectives (Figure 1). Our work is built upon the premise that complex geometries can be used to improve both the aesthetic and thermodynamic performance of passive building systems (Cupkova and Azel 2015) by actuating thermal performance through geometric parameters primarily due to convection. Currently, the engineering-oriented approach to the design of thermal mass relies on averaged thermal calculations (Holman 2002), which do not adequately describe the nuanced differences that can be produced by complex three-dimensional geometries of passive thermal mass systems. Using a combination of computational fluid dynamic simulations with physically measured data, we investigate the relationship of heat transfer coefficients related to parameters of surface geometry. Our measured results suggest that we can deliberately and significantly delay heat absorption re-radiation purely by changing the geometric surface pattern over the same thermal mass. The goal of this work is to offer designers a more robust rule set for understanding approximate thermal lag behaviors of complex geometric systems, with a focus on the design of geometric properties rather than complex thermal calculations.
keywords	design methods; information processing; physics; smart materials
series	ACADIA
email
last changed	2022/06/07 07:56

_id	cf2015_247
id	cf2015_247
authors	Demir, Gozdenur
year	2015
title	Analysis of Space Layout Using Attraction Force Model and Quadratic Assignment Problem
source	The next city - New technologies and the future of the built environment [16th International Conference CAAD Futures 2015. Sao Paulo, July 8-10, 2015. Electronic Proceedings/ ISBN 978-85-85783-53-2] Sao Paulo, Brazil, July 8-10, 2015, pp. 247-267.
summary	This paper researches the usefulness of computerized space layout programs in an actual problem of space layout of more than 50 design units of unequal sizes. This was tested with two existing space layout optimization methods, Quadratic Assignment Problem (QAP) and Attraction Force Model (AFM) as well as a satisficing method, intuitive approach. Necessary inputs for the evaluation processes, the evaluation processes and the resulting space layouts were analyzed for each approach by one designer. Their performance in the design process was criticized on subjects like preparation of inputs, situations related with multiple trials, evaluation of the resulting space layouts based on given inputs and what those space layouts represented. Generating alternatives is an advantage of computerized space layout approaches so that conditioning on the resulting space layouts decreases in the process but more research has to be done for their practicality in terms of input preparation, evaluation and transfer of outputs. Possible improvements were suggested to increase their usefulness in the professional field.
keywords	computerized space layout approaches, quadratic assignment problem, equilibrium method, intuitive approach
series	CAAD Futures
email
last changed	2015/06/29 07:55

_id	ecaade2015_119
id	ecaade2015_119
authors	Dokonal, Wolfgang; Knight, Michael W. and Dengg, Ernst Alexander
year	2015
title	New Interfaces - Old Models
doi	https://doi.org/10.52842/conf.ecaade.2015.1.101
source	Martens, B, Wurzer, G, Grasl T, Lorenz, WE and Schaffranek, R (eds.), Real Time - Proceedings of the 33rd eCAADe Conference - Volume 1, Vienna University of Technology, Vienna, Austria, 16-18 September 2015, pp. 101-106
summary	The rapid development of new Virtual Reality (VR) devices such as the Oculus Rift and Google Cardboard together with Augmented Reality (AR) applications such as 3Dplus (by the Finnish company advice) or gaming software such as Unity3D and Unreal Engine 4 raises the question of how we can use these new interfaces and applications to access our increasingly data-rich models. In this paper we will summarise the results of a joint international workshop where students explored the use of these new interfaces on existing models. During the course of the workshop, the students built their own VR environments to test spatial perception and then used different types of housing models with these interfaces to find out what kind of information inside those data rich models is best suited to be accessed using these new interfaces. The question will be if there is any added value - besides the novelty factor - in using these new devices in combination with old models. To give an extra dimension to the virtual nature of the workshop, students collaborated with some of the tutors primarily digitally using the virtual models and other online tools (Skype/Twitter/discussion boards). By having collaboration through the medium of the virtual interactive model as the core communication method, the amount, type and methods of presenting the information is tested and evaluated. This is work in progress and we had to experience several problems that we could not overcome in the available time.
wos	WOS:000372317300011
series	eCAADe
email
more	https://mh-engage.ltcc.tuwien.ac.at/engage/ui/watch.html?id=54a3a8e0-702c-11e5-9592-c7c2b292a6cf
last changed	2022/06/07 07:55

_id	ecaade2015_61
id	ecaade2015_61
authors	Foged, Isak Worre and Pasold, Anke
year	2015
title	Development of a Method and Model for Programming Material Behaviour in a Responsive Envelope
doi	https://doi.org/10.52842/conf.ecaade.2015.2.449
source	Martens, B, Wurzer, G, Grasl T, Lorenz, WE and Schaffranek, R (eds.), Real Time - Proceedings of the 33rd eCAADe Conference - Volume 2, Vienna University of Technology, Vienna, Austria, 16-18 September 2015, pp. 449-458
summary	The research presents an architectural method and model that organise material composites into weather-powered response building envelopes. The work is done through a set of simulation strategies including simulation of thermal sensation, simulation of material behaviours of a developed dynamic architectural envelope based on bi-material deflection and simulation of a design process based on evolutionary computation. The work finds that the proposed method and model can create dynamic expressive and environment-oriented functional building envelopes. The approach allow time-based articulation and making of architectures that respond to the thermal environment, thereby creating a basis for developing buildings that are intimately linked to dynamic environmental and human occupancy patterns.
wos	WOS:000372316000051
series	eCAADe
email
more	https://mh-engage.ltcc.tuwien.ac.at/engage/ui/watch.html?id=e70e19e4-70d7-11e5-9c6a-d7a061db2d21
last changed	2022/06/07 07:51

_id	caadria2015_096
id	caadria2015_096
authors	Fukuda, Tomohiro; Toshiki Tokuhara and Nobuy-Oshi Yabuki
year	2015
title	Development of A Kinematic Physical Model for Building Volume Simulation
doi	https://doi.org/10.52842/conf.caadria.2015.241
source	Emerging Experience in Past, Present and Future of Digital Architecture, Proceedings of the 20th International Conference of the Association for Computer-Aided Architectural Design Research in Asia (CAADRIA 2015) / Daegu 20-22 May 2015, pp. 241-250
summary	Both a physical model and VR are three-dimensional expression tools to enable intuitive understanding; however, both have pros and cons. Thus, this research took up the challenge of developing a kinematic physical model system for volume simulation of buildings or a city by using a physical model and VR data integrally. The developed system consists both of hardware which packed 105 lifting rods into a grid (the height of the rods could be changed individually by stepper motors) and of software which calculated the height of each rod from the VR data and lifted the rods. Through conducting verification experiments on the prototype system, a physical urban model could be produced in about two minutes, within acceptable error limits. In conclusion, the proposed method was evaluated as feasible and effective.
keywords	Kinematic model; physical model; Virtual Reality; rapid prototyping; building volume simulation; interaction.
series	CAADRIA
email
last changed	2022/06/07 07:50

_id	ecaade2015_247
id	ecaade2015_247
authors	Garcia, Manuel Jimenez and Retsin, Gilles
year	2015
title	Design Methods for Large Scale Printing
doi	https://doi.org/10.52842/conf.ecaade.2015.2.331
source	Martens, B, Wurzer, G, Grasl T, Lorenz, WE and Schaffranek, R (eds.), Real Time - Proceedings of the 33rd eCAADe Conference - Volume 2, Vienna University of Technology, Vienna, Austria, 16-18 September 2015, pp. 331-339
summary	With an exponential increase in the possibilities of computation and computer-controlled fabrication, high density information is becoming a reality in digital design and architecture. However, construction methods and industrial fabrication processes have not yet been reshaped to accommodate the recent changes in those disciplines. Although it is possible to build up complex simulations with millions of particles, the simulation is often disconnected from the actual fabrication process. Our research proposes a bridge between both stages, where one drives the other, producing a smooth transition from design to production. A particle in the digital domain becomes a drop of material in the construction method.The architect's medium of expression has become much more than a representational tool in the last century, and more recently it has evolved even beyond a series of rules to drive from design to production. The design system is the instruction itself; embedding structure, material and tectonics and gets delivered to the very end of the construction chain, where it gets materialised. The research showcased in this paper investigates tectonic systems associated with large scale 3D printing and additive manufacturing methods, inheriting both material properties and fabrication constraints at all stages from design to production. Computational models and custom design software packages are designed and developed as strategies to organise material in space in response to specific structural and logistical input.Although the research has developed a wide spectrum of 3D printing methods, this paper focuses only on two of the most recent projects, where different material and computational logics were investigated. The first, titled Filamentrics, intends to develop free-form space frames, overcoming their homogeneity by introducing robotic plastic extrusion. Through the use of custom made extruders a vast range of high resolution prototypes were developed, evolving the design process towards the fabrication of precise structures that can be materialised using additive manufacturing but without the use of a layered 3D printing method. Instead, material limitations were studied and embedded in custom algorithms that allow depositing material in the air for internal connectivity. The final result is a 3x2x2.5m structure that demonstrates the viability of this construction method for being implemented in more industrial scenarios.While Filamentrics is reshaping the way we could design and build light weight structures, the second project Microstrata aims to establish new construction methods for compression based materials. A layering 3D printing method combines both the deposition of the binder and the distribution of an interconnected network of capillaries. These capillaries are organised following structural principles, configuring a series of channels which are left empty within the mass. In a second stage aluminium is cast in this hollow space to build a continuous tension reinforcement.
wos	WOS:000372316000039
series	eCAADe
type	normal paper
email
more	https://mh-engage.ltcc.tuwien.ac.at/engage/ui/watch.html?id=07a6d8e0-6fe7-11e5-9994-cb14cd908012
last changed	2022/06/07 07:51

_id	ecaade2015_200
id	ecaade2015_200
authors	Gargaro, Silvia and Fioravanti, Antonio
year	2015
title	Towards a Context Knowledge Taxonomy - Combined Methodologies to Improve a Fast-Search Concept Extraction for an Ontology Population
doi	https://doi.org/10.52842/conf.ecaade.2015.1.137
source	Martens, B, Wurzer, G, Grasl T, Lorenz, WE and Schaffranek, R (eds.), Real Time - Proceedings of the 33rd eCAADe Conference - Volume 1, Vienna University of Technology, Vienna, Austria, 16-18 September 2015, pp. 137-147
summary	Context in Architectural Design can be defined-related-comparable to hypothesis and boundary conditions in mathematics. An eco-system that influences it by means of natural and artificial events, space and time dimension. The research has the aim to analyze the critical issues related to Context by providing a contribution to the study of interactions between Context Knowledge and Architectural Design and how it can be used to improve the performance of the buildings and reducing design mistakes. The research focusing on formal ontologies, has developed a model that enables a semantic approach to design application programs, to manage information, to answer design questions and to have a clear relation between the formal representation of the context domain and its meanings. This context model provides an advancement on the state of the art in simplified design assumptions, in term of ontology ambiguity and complexity reduction, by using algorithms to extract and optimize branches of the graph. The extraction does not limit the number of relations, that can be extended and improve context taxonomy coherency and accuracy.
wos	WOS:000372317300015
series	eCAADe
email
more	https://mh-engage.ltcc.tuwien.ac.at/engage/ui/watch.html?id=c8741aa2-702c-11e5-a273-83f9e53dafcf
last changed	2022/06/07 07:51

_id	ecaade2015_144
id	ecaade2015_144
authors	Kim, Sun-Joong; Choi, Yuri and Lee, Ji-Hyun
year	2015
title	Architectural Bioinspired Design: Functional Assessment of Design Terminologies to Support a Biological System Search - Functional Assessment of Design Terminologies to Support a Biological System Search
doi	https://doi.org/10.52842/conf.ecaade.2015.2.467
source	Martens, B, Wurzer, G, Grasl T, Lorenz, WE and Schaffranek, R (eds.), Real Time - Proceedings of the 33rd eCAADe Conference - Volume 2, Vienna University of Technology, Vienna, Austria, 16-18 September 2015, pp. 467-476
summary	In this study, the semantic relationship of lexicons from the architectural design domain and function words frequently used in the bioinspired design domain were quantitatively extracted. Even though bioinspired design for the architecture domain has a lot of possibility of use, it is not comparably accessible because the design supportive systems were focused on engineering design domain. Therefore, the semantic relatedness between function words from the engineering domain and lexicons from the architectural domain were quantified in order to develop a lexicon based biological system search tool. The lexicons were extracted from the texts of the International Building Code and natural language processing techniques supported the task. And the semantic relatedness between the lexicons and function words were quantified by the semantic network analysis using the WordNet system.
wos	WOS:000372316000053
series	eCAADe
email
last changed	2022/06/07 07:52

_id	caadria2015_004
id	caadria2015_004
authors	Kotsopoulos, Sotirios D. and Federico Casalegno
year	2015
title	Responsive Architectures
doi	https://doi.org/10.52842/conf.caadria.2015.335
source	Emerging Experience in Past, Present and Future of Digital Architecture, Proceedings of the 20th International Conference of the Association for Computer-Aided Architectural Design Research in Asia (CAADRIA 2015) / Daegu 20-22 May 2015, pp. 335-344
summary	Real-time supply of computational power into built environments enables to re-address questions of user experience, comfort and building performance. This presentation discusses the features of responsive architecture through the example of a ‘programmable window’ that was designed and deployed in a prototype house, in Trento, N. Italy. In the example the parts and functionalities of building skins were revisited, to integrate advances in electroactive materials, information communication technologies and control systems engineering.
keywords	Electroactive materials; model-based control; programmable windows.
series	CAADRIA
email
last changed	2022/06/07 07:51

For more results click below: